GitLab

This patch does two main things

- It implements the crash console UART init in assembly, as a
  hard-coded 115200 8N1 assumed from the 24 MHz clock.

  If the clock setup code has not run yet, this code can't work but,
  setting up clocks and clock-gates is way out of scope for this type of
  recovery function.

- It adds code to write a character out of the NXP UART without using any
  stack-based operations when doing so.

- Provides support for crash console in DCE or DTE mode.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

- Adds a simple register read/write abstraction to cut-down on the
  amount of typing and text required to access UART registers in this driver.

- Adds a console getc() callback.

- Adds a console putc() callback, translating '\n' to '\r' + '\n'.

- Initializes the MXC UART, take a crude method of calculating the
  BAUD rate generator. The UART clock-gates must have been enabled prior
  to launching the UART init code.
  Special care needs to be taken to ensure the UBIR is initialized before the
  UBMR and we need to ensure that UCR2.SRST comes good before trying to
  program other registers associated with the UART.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Change-Id: Ifdb0ceec19d267b14d796b5d31f08f7342190484
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I2954a99d5b72069bcb7bac9d6926c6209d6ba881
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I08447b44fffb6e54f9fab957eee369ccbda4247a
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I6a2adef87c20f9279446a54b7e69618fba3d2a25
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I945029ca26ea2e63f0d92c5f33019b882f23bd72
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ib587f12f36810fc7d4f4b8f575195554299b8ed4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

tf_printf and tf_snprintf are now called printf and snprintf, so the
code needs to be updated.

Change-Id: Iffeee97afcd6328c4c2d30830d4923b964682d71
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This allows the console drivers to be implemented in C

Change-Id: Ibac859c4bcef0e92a0dcacc6b58ac19bc69b8342
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

The CCI500 TRM explicitily requires completion of the write
operation before the read operation, and it is not guaranteed
by dmb but it is dsb.

Change-Id: Ieeaa0d1a4b8fcb87108dea9b6de03d9c8a150829
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Because of -Werror, this causes a build error.

Change-Id: I37a8c4bbfe3f2ced5e17981a2814985919ad483b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Replace emmc framework by mmc framework.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Migrate dw_mmc driver from emmc framework to mmc framework. The
emmc framework will be abandoned.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

It should set buswidth and speed of mmc controller before accessing
mmc.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

DMA is always used in mmc driver. So the buffer address should
always follow the DMA limitation.

There're same requirement in mmc_read_blocks()/mmc_write_blocks()
on parameter buf. Since parameter buf comes from io_block driver,
it's already handled in io_block driver.

At here, just make the minimum address alignment on 16 chars.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

mmc_read_blocks()/mmc_write_blocks() derived from io_block_ops_t
type. It means that lba param should be integer type, not
unsigned integer type.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Sending CMD8 before CMD1 just causes to fetch data failure in eMMC.
Check whether it's eMMC first. If it's eMMC, send CMD1 command instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Functions provided by stdio.h such as printf and sprintf are available
in the codebase, but they add a lot of code to the final image if they
are used:

- AArch64: ~4KB
- AArch32: ~2KB in T32, ~3KB in A32

tf_printf and tf_snprintf are a lot more simple, but it is preferable
to use them when possible because they are also used in common code.

Change-Id: Id09fd2b486198fe3d79276e2c27931595b7ba60e
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

We had exit but we didn't have atexit, and we were calling panic and
tf_printf from exit, which generated a dependency from exit to them.
Having atexit allows to set a different function pointer in every image.

Change-Id: I95b9556d680d96249ed3b14da159b6f417da7661
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Mbebtls include paths are controlled by the user using the variable
MBEDTLS_DIR and they are out of the TF source tree. Since these
includes have a different origin it is better to move them to a
different variable.

This change makes easier for the romlib Makefile to parse the include
paths.

Change-Id: I3e4c99300f1012bc7f88c6b9f5bc0ec1f7b5aa8d
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

TF Makefile was linking all the objects files generated for the
Mbed TLS library instead of creating a static library that could be
used in the linking stage.

Change-Id: I8e4cd843ef56033c9d3faeee71601d110b7e4c12
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

A new function mmc_reset_to_idle is also created.
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Fix violations of MISRA C-2012 Rules 10.1, 10.3 and 10.4.

Change-Id: I13c6acda798c1666892f630f097a23e68748f9e4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

When a platform enables its caches before it initializes the
GICC/GICR interface then explicit cache maintenance is not
needed. Remove these here.
Signed-off-by: Andrew F. Davis <afd@ti.com>

The DDR driver is under dual license, BSD and GPLv2.
The configuration parameters are taken from device tree.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

If a PMIC companion chip is present on board, it has to be configured
for regulators supplies.
This check is done with board DT configuration.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

The management of pinctrl nodes of device tree is also added.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

The clock driver is under dual license, BSD and GPLv2.
The clock driver uses device tree, so a minimal support for this is added.
The required files for driver and DTS files are in include/dt-bindings/.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

STM32MP1 is a microprocessor designed by STMicroelectronics,
based on a dual Arm Cortex-A7.
It is an Armv7-A platform, using dedicated code from TF-A.

STM32MP1 uses BL2 compiled with BL2_AT_EL3.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>

The functions cci_enable_snoop_dvm_reqs and cci_disable_snoop_dvm_reqs write
in the SNOOP_CTRL_REGISTER of the slave interface and it polls the status
register to be sure that the operation is finished before leaving the
functions. If the write in SNOOP_CTRL_REGISTER is reordered after the first
read in the status register then these functions can finish before
enabling/disabling snoops and DVM messages.

The CCI500 TRM specifies:

	Wait for the completion of the write to the Snoop Control Register
	before testing the change_pending bit.

Change-Id: Idc7685963f412be1c16bcd3c6e3cca826e2fdf38
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Remove assert on buffer address equal zero.
Marvell uses address 0x0 for loading BL33,
so this check is irrelevant and breaks the
debug builds on Marvell platforms.

Change-Id: Ie56a51138e2e4ddd8986dd7036797dc2d8b10125
Signed-off-by: Haim Boot <hayim@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/54589

Add i2c driver for A8K SoC family.

Change-Id: I5932b2fce286d84fc3ad5a74c4c456001faa3196
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Add COMPHY driver for usage in a runtime service.

Change-Id: I6fb42d0a099496d5699ee24684ae2b93ed35770b
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Add thermal driver for A8K SoC family.
The termal unit data is used by Marvell DRAM initialization
code for optimizing the memory controller configuration

Change-Id: Iad92689fa6e4224a89d872e9aa015393abd9cf73
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Add LLC (L3) cache management drivers for Marvell SoCs
AP806, AP807 and AP810

Change-Id: Ic70710f9bc5b6b48395d62212df7011e2fbb5894
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Add ModularChip and MCI drivers for A8K SoC family.
ModularChip drivers include support for the internal building
blocks of Marvell ARMADA SoCs - APN806, APN807 and CP110

Change-Id: I9559343788fa2e5eb47e6384a4a7d47408787c02
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Add address decoding unit drivers for Marvell SoCs.

Address decoding flow and address translation units chart
are located at docs/marvell/misc/mvebu-a8k-addr-map.txt

Change-Id: Id6ce311fa1f4f112df3adfac5d20449f495f71ed
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

This change is largely based on existing eMMC framework by Haojian Zhuang
(@hzhuang1).

The MMC framework supports both eMMC and SD card devices. It was
written as a new framework since breaking few eMMC framework APIs.

At card probe and after the reset to idle command (CMD0), a Send
Interface Condition Command is sent (CMD8) to distinguish between
eMMC and SD card devices. eMMC devices go through the same
sequence as in the former eMMC framework. Else the framework
uses commands dedicated to SD-cards for init or frequency switch.

A structure is created to share info with the driver. It stores:
- the MMC type (eMMC, SD or SD HC)
- the device size
- the max frequency supported by the device
- the block size: 512 for eMMC and SD-HC and read from CSD
 structure for older SD-cards

Restriction to align buffers on block size has been removed.
Cache maintenance was removed and is expected to be done in the platform
or device driver.

The MMC framework includes some MISRA compliance coding style
maybe not yet ported in the existing eMMC framework.

Fixes ARM-software/tf-issues#597
Signed-off-by: Yann Gautier <yann.gautier@st.com>