GitLab

The codebase was using non-standard headers. It is needed to replace
them by the correct ones so that we can use the new libc headers.

Change-Id: I530f71d9510cb036e69fe79823c8230afe890b9d
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The patch changes the layout of BL images in memory to enable
more efficient use of available space. Previously BL31 was loaded
with the expectation that BL2 memory would be reclaimed by BL32
loaded in SRAM. But with increasing memory requirements in the
firmware, we can no longer fit BL32 in SRAM anymore which means the
BL2 memory is not reclaimed by any runtime image. Positioning BL2
below BL1-RW and above BL31 means that the BL31 NOBITS can be
overlaid on BL2 and BL1-RW.

This patch also propogates the same memory layout to BL32 for AArch32
mode. The reset addresses for the following configurations are also
changed :
   * When RESET_TO_SP_MIN=1 for BL32 in AArch32 mode
   * When BL2_AT_EL3=1 for BL2

The restriction on BL31 to be only in DRAM when SPM is enabled
is now removed with this change. The update to the firmware design
guide for the BL memory layout is done in the following patch.

Change-Id: Icca438e257abe3e4f5a8215f945b9c3f9fbf29c9
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This function implements the platform dependant part of PSCI system
reset2 for CSS platforms using SCMI.

Change-Id: I724389decab484043cadf577aeed96b349c1466d
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

The common implementation of css_scp_sys_shutdown and
css_scp_warm_reset is refactored into a new function,
css_scp_system_off() that allows the desired power state to be
specified.

The css_scp_system_off can be used in the implementation of
SYSTEM_RESET2 for PSCI v1.1.

Change-Id: I161e62354d3d75f969b8436d794335237520a9a4
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch does the required changes to enable CSS platforms
to build and use the SDS framework. Since SDS is always coupled with
SCMI protocol, the preexisting SCMI build flag is now renamed to
`CSS_USE_SCMI_SDS_DRIVER` which will enable both SCMI and SDS on
CSS platforms. Also some of the workarounds applied for SCMI are
now removed with SDS in place.

Change-Id: I94e8b93f05e3fe95e475c5501c25bec052588a9c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The SCP_BL2 is transferred to SCP during BL2 image load and authenticate
sequence. The Boot-Over-MHU (BOM) protocol is used as transport for this. After
the SCP boots using the transferred image, the AP CPU waits till the `READY`
message is received from SCP. This patch separates the API for transport of
image from the wait for `READY` message and also moves the related files to
the `css/drivers` folder. The previous API `scp_bootloader_transfer` is
renamed to `css_scp_boot_image_xfer` to reflect the css naming convention.
This reorganisation also allows easier switch to a different transport
(eg: Shared Data Structure based transfer) in future

Change-Id: I8a96f9c4616ffde6dbfdf7c18f6f6f8bfa40bbf0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch introduces an additional layer of abstraction between
CSS power management hooks and the SCPI driver. A new set of APIs
are introduced in order to abstract out power management operations
from underlying communication mechanism with the SCP.

The SCPI and the associated MHU drivers are moved into a `drivers`
folder in CSS. The new SCP communication abstraction layer is added
in the `drivers/scp` folder. The existing CSS power management
uses the new APIs to reflect this abstraction.

Change-Id: I7d775129fc0558e9703c2724523fb8f0a916838c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Add delay timer implementation based on the system generic counter.
This either uses the platform's implementation of
`plat_get_syscnt_freq()` or explicit clock multiplier/divider values
provided by the platform.

The current implementation of udelay has been modified to avoid
unnecessary calculations while waiting on the loop and to make it
easier to check for overflows.

Change-Id: I9062e1d506dc2f68367fd9289250b93444721732

Add PL061 GPIO driver that is depend on gpio framework.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

This patch adds a CoT based on the Trusted Board Boot Requirements
document*. The CoT consists of an array of authentication image
descriptors indexed by the image identifiers.

A new header file with TBBR image identifiers has been added.
Platforms that use the TBBR (i.e. ARM platforms) may reuse these
definitions as part of their platform porting.

PLATFORM PORT - IMPORTANT:

Default image IDs have been removed from the platform common
definitions file (common_def.h). As a consequence, platforms that
used those common definitons must now either include the IDs
provided by the TBBR header file or define their own IDs.

*The NVCounter authentication method has not been implemented yet.

Change-Id: I7c4d591863ef53bb0cd4ce6c52a60b06fa0102d5

This patch adds a tool that generates all the necessary elements
to establish the chain of trust (CoT) between the images.

The tool reads the binary images and signing keys and outputs the
corresponding certificates that will be used by the target at run
time to verify the authenticity of the images.

Note: the platform port must provide the file platform_oid.h. This
file will define the OIDs of the x509 extensions that will be added
to the certificates in order to establish the CoT.

Change-Id: I2734d6808b964a2107ab3a4805110698066a04be

This patch implements the TSP on Juno. It executes from on-chip Trusted
SRAM.

Also, the other bootloader images (i.e. BL1 R/W, BL2 and BL3-1) have
been moved around. The reason is, although there was enough space
overall to store the TSP in SRAM, there was no contiguous free chunk
of SRAM big enough to hold it.

This patch keeps the overall memory layout (i.e. keeping BL1 R/W at
the bottom, BL2 at the top and BL3-1 in between) but moves the base
addresses of all the bootloader images in such a way that:
 - memory fragmentation is reduced enough to fit BL3-2 in;
 - new base addresses are suitable for release builds as well as debug
   ones;
 - each image has a few extra kilobytes for future growth.
   BL3-1 and BL3-2 are the images which received the biggest allocations
   since they will most probably grow the most.

This patch also adds instruction synchronization barriers around the code which
handles the timer interrupt in the TSP. This ensures that the interrupt is not
acknowledged after or EOIed before it is deactivated at the peripheral.

Change-Id: I1c5b51858700027ee283ac85d18e06863a27c72e

This patch adds the initial port of the ARM Trusted Firmware on the Juno
development platform. This port does not support a BL3-2 image or any PSCI APIs
apart from PSCI_VERSION and PSCI_CPU_ON. It enables workarounds for selected
Cortex-A57 (#806969 & #813420) errata and implements the workaround for a Juno
platform errata (Defect id 831273).

Change-Id: Ib3d92df3af53820cfbb2977582ed0d7abf6ef893

Move the remaining IO storage source file (io_storage.c) from the
lib to the drivers directory. This requires that platform ports
explicitly add this file to the list of source files.

Also move the IO header files to a new sub-directory, include/io.

Change-Id: I862b1252a796b3bcac0d93e50b11e7fb2ded93d6

Update code base to remove variables from the .data section,
mainly by using const static data where possible and adding
the const specifier as required. Most changes are to the IO
subsystem, including the framework APIs. The FVP power
management code is also affected.

Delay initialization of the global static variable,
next_image_type in bl31_main.c, until it is realy needed.
Doing this moves the variable from the .data to the .bss
section.

Also review the IO interface for inconsistencies, using
uintptr_t where possible instead of void *. Remove the
io_handle and io_dev_handle typedefs, which were
unnecessary, replacing instances with uintptr_t.

Fixes ARM-software/tf-issues#107.

Change-Id: I085a62197c82410b566e4698e5590063563ed304

Reduce the number of header files included from other header
files as much as possible without splitting the files. Use forward
declarations where possible. This allows removal of some unnecessary
"#ifndef __ASSEMBLY__" statements.

Also, review the .c and .S files for which header files really need
including and reorder the #include statements alphabetically.

Fixes ARM-software/tf-issues#31

Change-Id: Iec92fb976334c77453e010b60bcf56f3be72bd3e

Move almost all system include files to a logical sub-directory
under ./include. The only remaining system include directories
not under ./include are specific to the platform. Move the
corresponding source files to match the include directory
structure.

Also remove pm.h as it is no longer used.

Change-Id: Ie5ea6368ec5fad459f3e8a802ad129135527f0b3

The modified implementation uses the IO abstraction rather than
making direct semi-hosting calls.  The semi-hosting driver is now
registered for the FVP platform during initialisation of each boot
stage where it is used.  Additionally, the FVP platform includes a
straightforward implementation of 'plat_get_image_source' which
provides a generic means for the 'load_image' function to determine
how to access the image data.

Change-Id: Ia34457b471dbee990c7b3c79de7aee4ceea51aa6

Ctags seem to have a problem with generating tags for assembler symbols
when a comment immediately follows an assembly label.

This patch inserts a single space character between the label
definition and the following comments to help ctags.

The patch is generated by the command:

  git ls-files -- \*.S | xargs sed -i 's/^\([^:]\+\):;/\1: ;/1'

Change-Id: If7a3c9d0f51207ea033cc8b8e1b34acaa0926475

Change-Id: Ic7fb61aabae1d515b9e6baf3dd003807ff42da60

- Add instructions for contributing to ARM Trusted Firmware.

- Update copyright text in all files to acknowledge contributors.

Change-Id: I9311aac81b00c6c167d2f8c889aea403b84450e5