GitLab

Update to support new part numbers.

Add new STM32 MPUs Part = STM32MP151F, STM32MP153F, STM32MP157F,
STM32MP151D, STM32MP153D, STM32MP157D

The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
              3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
              and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz

Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :

- A      Basic + Cortex-A7 @ 650 MHz
- C      Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D      Basic + Cortex-A7 @ 800 MHz
- F      Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz

Remove useless variable in stm32mp_is_single_core().

Change-Id: Id30c836af986c6340c91efa8a7ae9480a2827089
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Add a new revision of STM32MP15x CPU (Rev.Z).

Change-Id: I227dd6d9b3fcc43270015cfb21f60aeb0a8ab658
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>

SCMI shared memory is used to exchange message payloads between
secure SCMI services and non-secure SCMI agents. It is mapped
uncached (device) mainly to conform to existing support in
the Linux kernel. Note that executive messages are mostly short
(few 32bit words) hence not using cache will not penalize much
performances.

Platform stm32mp1 shall configure ETZPC to harden properly the
secure and non-secure areas of the SYSRAM address space, that before
CPU accesses the shared memory when mapped non-secure.

This change defines STM32MP_SEC_SYSRAM_BASE/STM32MP_SEC_SYSRAM_SIZE and
STM32MP_NS_SYSRAM_BASE/STM32MP_NS_SYSRAM_SIZE.

Change-Id: I71ff02a359b9668ae1c5a71b5f102cf3d310f289
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

New helper functions to get GPIO banks configuration from the FDT.

stm32_get_gpio_bank_pinctrl_node() allows stm32mp platforms to
differentiate specific GPIO banks when these are defined with a specific
path in the FDT.

fdt_get_gpio_bank_pin_count() returns the number of pins in a GPIO bank
as it depends on the SoC variant.

Change-Id: I4481774152b3c6bf35bf986f58e357c2f9c19176
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

Relation between GPIO banks and their base address and offset address
if platform dependent. This change moves helper functions
stm32_get_gpio_bank_base() and stm32_get_gpio_bank_offset() from
plat/st/common to plat/st/stm32mp1/.

Change-Id: Id3d03e585746aa5509c6fab7d88183a92d561e3f
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

This function gets the DDR size from DT, and withdraws (if defined) the
sizes of secure DDR and shared memory areas.
This function also checks DT values fits the default DDR range.
This non-secure memory is available for BL33 and non-secure OS.

Change-Id: I162ae5e990a0f9b6b7d07e539de029f1d61a391b
Signed-off-by: Yann Gautier <yann.gautier@st.com>

This BSEC service is a platform specific service. Implementation
moved to the platform part.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I1f70ed48a446860498ed111acce01187568538c9

Among the variants of STM32MP, the STM32MP151 is a single Cortex-A7 chip.
A function is added to check the part number of the SoC.
If it corresponds to STM32MP151A or STM32MP151C, then the chip has a single
Cortex-A7.

Change-Id: Icac2015c5d03ce0bcb8e99bbaf1ec8ada34be49c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

On STMicroelectronics boards, the board information is stored in OTP.
This OTP is described in device tree, in BSEC board_id node.

Change-Id: Ieccbdcb048343680faac8dc577b75c67ac106f5b
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

This information is located in DBGMCU registers.

Change-Id: I480aa046fed9992e3d9665b1f0520bc4b6cfdf30
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Introduce driver for STM32 IWDG peripheral (Independent Watchdog).
It is configured according to device tree content and should be enabled
from there.
The watchdog is not started by default. It can be started after an HW
reset if the dedicated OTP is fused.

The watchdog also needs to be frozen if a debugger is attached.
This is done by configuring the correct bits in DBGMCU.
This configuration is allowed by checking BSEC properties.

An increase of BL2 size is also required when adding this new code.

Change-Id: Ide7535d717885ce2f9c387cf17afd8b5607f3e7f
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

GPIOx clocks are specific to each STM32MP platforms.
This change moves function stm32_get_gpio_bank_clock() from stm32mp
common source files to platform private stm32mp1_private.c source file.

Change-Id: I9616c0d3fe4d10af715d6f2d1550c13ab62c829a
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Mainly remove suffix 1 from prefix stm32mp1 in several macros and functions
that can be used in drivers shared by different platforms.

Change-Id: I2295c44f5b1edac7e80a93c0e8dfd671b36e88e7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

Some parts of code could be shared with platform derivatives,
or new platforms.
A new folder plat/st/common is created to put common parts.

stm32mp_common.h is a common API aggregate.

Remove some casts where applicable.
Fix some types where applicable.
Remove also some platform includes that are already in stm32mp1_def.h.

Change-Id: I46d763c8d9e15732d1ee7383207fd58206d7f583
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>