GitLab

This the patch replaces the DSB SY with DSB ISH
after disabling L2 prefetches during the Cortex-A57
power down sequence.

Change-Id: I048d12d830c1b974b161224eff079fb9f8ecf52d

Prior to this patch, the errata workarounds were applied for any version
of the CPU in the release build and in the debug build an assert
failure resulted when the revision did not match. This patch applies
errata workarounds in the Cortex-A57 reset handler only if the 'variant'
and 'revision' fields read from the MIDR_EL1 match. In the debug build,
a warning message is printed for each errata workaround which is not
applied.

The patch modifies the register usage in 'reset_handler` so
as to adhere to ARM procedure calling standards.

Fixes ARM-software/tf-issues#242

Change-Id: I51b1f876474599db885afa03346e38a476f84c29

This patch adds level specific cache maintenance functions
to cache_helpers.S. The new functions 'dcsw_op_levelx',
where '1 <= x <= 3', allow to perform cache maintenance by
set/way for that particular level of cache.  With this patch,
functions to support cache maintenance upto level 3 have
been implemented since it is the highest cache level for
most ARM SoCs.

These functions are now utilized in CPU specific power down
sequences to implement them as mandated by processor specific
technical reference manual.

Change-Id: Icd90ce6b51cff5a12863bcda01b93601417fd45c

FVP: keep shared data in Trusted SRAM

Juno: Support entry into a standby state

Jc/juno mem 6

This patch deprecates the build option to relocate the shared data
into Trusted DRAM in FVP. After this change, shared data is always
located at the base of Trusted SRAM. This reduces the complexity
of the memory map and the number of combinations in the build
options.

Fixes ARM-software/tf-issues#257

Change-Id: I68426472567b9d8c6d22d8884cb816f6b61bcbd3

This patch adds support on the Juno platform for entering a wfi in
response to a PSCI CPU_SUSPEND call where the state type is a
standby state.

Change-Id: I0a102dee1f8d2ad936c63ad1d1d3ad001a4a4768

This patch configures the TrustZone Controller in Juno to split
the 2GB DDR-DRAM memory at 0x80000000 into Secure and Non-Secure
regions:

- Secure DDR-DRAM: top 16 MB, except for the last 2 MB which are
  used by the SCP for DDR retraining
- Non-Secure DDR-DRAM: remaining DRAM starting at base address

Build option PLAT_TSP_LOCATION selects the location of the secure
payload (BL3-2):

- 'tsram' : Trusted SRAM (default option)
- 'dram'  : Secure region in the DDR-DRAM (set by the TrustZone
            controller)

The MMU memory map has been updated to give BL2 permission to load
BL3-2 into the DDR-DRAM secure region.

Fixes ARM-software/tf-issues#233

Change-Id: I6843fc32ef90aadd3ea6ac4c7f314f8ecbd5d07b

Reset CNTVOFF_EL2 register before exit into EL1 on warm boot

This patch replaces direct accesses to the TZC-400 registers by the
appropiate calls to the generic driver available in the Trusted
Firmware in order to initialize the TrustZone Controller.

Functions related to the initialization of the secure memory,
like the TZC-400 configuration, have been moved to a new file
'plat_security.c'. This reorganization makes easier to set up
the secure memory from any BL stage.

TZC-400 initialization has been moved from BL1 to BL2 because BL1
does not access the non-secure memory. It is BL2's responsibility
to enable and configure the TZC-400 before loading the next BL
images.

In Juno, BL3-0 initializes some of the platform peripherals, like
the DDR controller. Thus, BL3-0 must be loaded before configuring
the TrustZone Controller. As a consequence, the IO layer
initialization has been moved to early platform initialization.

Fixes ARM-software/tf-issues#234

Change-Id: I83dde778f937ac8d2996f7377e871a2e77d9490e

Create BL stage specific translation tables

This patch uses the IMAGE_BL<x> constants to create translation tables specific
to a boot loader stage. This allows each stage to create mappings only for areas
in the memory map that it needs.

Fixes ARM-software/tf-issues#209

Change-Id: Ie4861407ddf9317f0fb890fc7575eaa88d0de51c

Remove BSS section access by 'plat_print_gic' during crash reporting

This patch avoids the problem of crash reporting mechanism accessing
global data in BSS by 'plat_print_gic_regs' for FVP platforms. Earlier
it depended on the global 'plat_config' object for the GIC Base address
in FVP platforms which would have caused exception if it were accessed
before the BSS was initialized. It is now fixed by dynamically
querying the V2M_SYS_ID to find the FVP model type and accordingly
selecting the appropriate GIC Base address.

This patch also fixes the 'plat_print_gic_regs' to use the correct GIC
Distributor base address for printing GICD_IS_PENDR register values
for both Juno and FVP platforms.

Fixes ARM-Software/tf-issues#236

Change-Id: I545c7b908b3111419bf27db0575ce86acf86784b

Fix LENGTH attribute value in linker scripts

This patch fixes the incorrect value of the LENGTH attribute in
the linker scripts. This attribute must define the memory size, not
the limit address.

Fixes ARM-software/tf-issues#252

Change-Id: I328c38b9ec502debe12046a8912d7dfc54610c46

Dispatcher for OPTEE from Linaro SWG

Adds a dispatcher for OP-TEE based on the test secure payload
dispatcher.

Fixes arm-software/tf-issues#239

Initializes SCTLR_EL1 based on MODE_RW bit in SPSR for the entry
point. The RES1 bits for SCTLR_EL1 differs for Aarch64 and Aarch32
mode.

Add support for specifying pre-built BL binaries in Makefile

This patch adds support for supplying pre-built BL binaries for BL2,
BL3-1 and BL3-2 during trusted firmware build. Specifying BLx = <path_to_BLx>
in the build command line, where 'x' is any one of BL2, BL3-1 or BL3-2, will
skip building that BL stage from source and include the specified binary in
final fip image.

This patch also makes BL3-3 binary for FIP optional depending on the
value of 'NEED_BL33' flag which is defined by the platform.

Fixes ARM-software/tf-issues#244
Fixes ARM-software/tf-issues#245

Change-Id: I3ebe1d4901f8b857e8bb51372290978a3323bfe7

This patch resets the value of CNTVOFF_EL2 before exit to EL1 on
warm boot. This needs to be done if only the Trusted Firmware exits
to EL1 instead of EL2, otherwise the hypervisor would be responsible
for this.

Fixes ARM-software/tf-issues#240

Change-Id: I79d54831356cf3215bcf1f251c373bd8f89db0e0

Documentation for version 1.0

Fix minor issues in user guide

Final updates to readme.md and change-log.md for ARM Trusted
Firmware version 1.0. Also increment the version in the Makefile.

Change-Id: I00fe1016c8b936834bbf7bbba7aab07f51261bbb

*   Fix broken link to SCP download.

*   Remove requirement to install `ia32-libs`. This package is no
    longer available in current versions of Ubuntu and is no
    longer required when using the Linaro toolchain.

Change-Id: I9823d535a1d69136685754b7707b73e1eef0978d

Miscellaneous documentation fixes

This patch gathers miscellaneous minor fixes to the documentation, and comments
in the source code.

Change-Id: I631e3dda5abafa2d90f464edaee069a1e58b751b
Co-Authored-By: Soby Mathew <soby.mathew@arm.com>
Co-Authored-By: Dan Handley <dan.handley@arm.com>

Add information about Juno in firmware-design.md

This patch reorganizes the firmware design guide to add information about the
port of the ARM Trusted Firmware to the Juno ARM development platform.

Change-Id: I0b80e2e7a35ccad1af2e971506cfb7fe505f8b84

Fix reset to BL3-1 instructions in user guide, part 2

Add Juno instructions to user guide

This patch makes the Trusted Firmware build instructions in the
user guide platform independent.

FVP specific instructions have been grouped together under a new
section dedicated to FVP.

Juno specific instructions to build and run the Trusted Firmware,
UEFI and Linux have been added.

Change-Id: I9bfb1b9d732b1f73abbe29f68ac931e1773a4fd5

Fix the instructions for resetting to the BL3-1 entrypoint in the
user guide. The BL3-1 and BL3-2 image locations changed in the fix
to ARM-software/tf-issues#100 (commit 186c1d4b). This is distinct
from the similar issue fixed in commit bfb1dd51.

Also clarify the dependence on the FVP_SHARED_DATA_LOCATION and
FVP_TSP_RAM_LOCATION build options, and tidy up the "Notes
regarding Base FVP configuration options" section.

Change-Id: I6b03452a71f0c69efa169852712bcb184242696e

Move up dependency versions in user guide

Rationalize UART usage among different BL stages

This patch changes the UART port assignment for various BL stages
so as to make it consistent on the platform ports. The BL1, BL2 and
BL3-1 now uses UART0 on the FVP port and SoC UART0 on the Juno port.
The BL3-2 uses UART2 on the FVP port and FPGA UART0 on the Juno
port.

This provides an interim fix to ARM-software/tf-issues#220 until
support is added for changing the UART port for a BL image between
cold boot and runtime.

Change-Id: Iae5faea90be3d59e41e597b34a902f93e737505a

Move up the version numbers of the following Trusted Firmware
dependencies in the user guide:

*   Foundation and Base FVPs (latest publically available
    versions).

*   EDK2 implementation. The guide now uses the latest version from
    https://github.com/ARM-software/edk2.git. This requires the
    `iasl` package to also be installed.

*   Linux kernel. The guide now uses the latest version from
    https://github.com/ARM-software/linux.git.

*   Linaro OpenEmbedded file system.

*   ARM Development Studio 5.

Change-Id: I95bb863a61e47b9ef8be3d110f7087375ee78add

Add support for Juno in Trusted Firmware