GitLab

Correct function header of pm_api_clock_getparent() and
pm_api_clock_setparent().
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Acked-by: Will Wong <WILLW@xilinx.com>

PLL type clock is enabled by FSBL on boot-up. PMUFW enable/disable
them based on their user count. So, it should not be handled from ATF.

Put PLL type clock into bypass and reset mode only while changing
PLL rate (FBDIV).
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

This patch adds new API's for performing pl configuration
readback.
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

CCF has already provision to enable clock during registration
through CLK_IS_CRITICAL flag. Use CLK_IS_CRITICAL instead of
init_enable attribute.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Jolly Shah <jolly.shah@xilinx.com>

WDT used by APU is FPD_WDT. FPD WDT clock is controlled by
FPD_SLCR.WDT_CLK_SEL register. Correct the same in WDT clock
database.

As per FPD_SLCR.WDT_CLK_SEL register, there can be only two
parents of WDT clock not three. Fix the same by correcting it's
parents in clock database.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Jolly Shah <jolly.shah@xilinx.com>

Add support for writing to AFI registers.
So that after writing a bitstream the interface can be programmed.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Since the MMIO read/write APIs are removed from Linux user space,
Linux cannot directly write to the Global General Storage Register 4
any more to set healthy boot status.

Create an IOCTL to allow Linux to set boot health status.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Will Wong <willw@xilinx.com>

To make ULPI transceiver work, a HIGH - LOW - HIGH pulse needs
to be given to resetb pin of ULPI chip. In ZYNQMP, this resetb
pin is being driven by BOOT MODE PIN 1. The BOOT MODE PIN's
are controlled by BOOT_PIN_CTRL register present in CRL_APB
address region. Since CRL_APB can be resticted to secure access,
this pin should be controlled by ATF.

This patch adds the support for the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Currently in Linux maximum number of clocks is hard-coded and
so it needs to allocate static memory. It can get actual clock
number after querying all clock names by special clock name
string. Add new query data parameter to get actual number of
clocks so Linux can get actual clock numbers in advance.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>

Change arm_setup_page_tables() to take a variable number of memory
regions. Remove coherent memory region from BL1, BL2 and BL2U as
their coherent memory region doesn't contain anything and
therefore has a size of 0. Add check to ensure this
doesn't change without us knowing.

Change-Id: I790054e3b20b056dda1043a4a67bd7ac2d6a3bc0
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Also change header guards to fix defects of MISRA C-2012 Rule 21.1.

Change-Id: Ied0d4b0e557ef6119ab669d106d2ac5d99620c57
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch reads the chipid registers directly instead of making
pm call when running at BL32. User should ensure that these registers
should always be accessed from APU in their system configuration.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

This patch builds ATF to DDR if SPD is enabled as it cant fit in
On chip memory(OCM) with SPD enabled. This solves the issue
of build failure with SPD enabled for ZynqMP platform.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

RFC4122 defines that fields are stored in network order (big endian),
but TF-A stores them in machine order (little endian by default in TF-A).
We cannot change the future UUIDs that are already generated, but we can store
all the bytes using arrays and modify fiptool to generate the UUIDs with
the correct byte order.

Change-Id: I97be2d3168d91f4dee7ccfafc533ea55ff33e46f
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch adds support to restart system incase of wdt
timeout.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

The vcu disable bit in efuse ipdisable register is valid
only if PL powered up so, consider PL powerup status for
determing EG/EV part. If PL is not powered up, display
EG/EV as a part of string. The PL powerup status will
be filled by pmufw based on PL PROGB status in the
9th bit of version field.This patch also used IPI
to get this info from pmufw instead of directly accessing
the registers. Accessing this info from pmufw using
IPI fixes the issue of PMUFW access denied error for
reading IPDISABLE register.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

This patch adds new API for processing secure images. This API
is used for authentication and decryption of secure images using
xilsecure in pmufw.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Existing code blocks each IPI send request in ipi_mb_notify()
function till pmu clears respective bit in ipi observation
register.

After sending PM_SYSTEM_SHUTDOWN request to PMU, PMU will
restart APU. While PMU is restarting APU, ATF is running out
of OCM, which can cause read/write hang from/to OCM.
There is no need to wait for notification from PMU in case
of SystemShutdown request in ATF, as APU is going to restart.

This patch fixes APU only restart issue.
Signed-off-by: Tejas Patel <tejasp@xilinx.com>
Acked-by: Wendy Liang <wendy.liang@xilinx.com>

This patch makes bitstream load blocking call and waits until
bitstream is loaded successfully or return with error.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Avesh Khan <aveshk@xilinx.com>

GET_CALLBACK_DATA function is not required now. IPI mailbox
can be used instead of GET_CALLBACK_DATA function.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

PMU IPI-1 is used for callbacks from PMU to master. Unsecure
master can also receive callbacks from PMU, so make PMU IPI-1
as non-secure.

All requests from master(s) to PMU would still go on PMU IPI-1
secure channel.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>

Remove includes of gic_common.h and string.h which
are not required.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Acked-by: Jolly Shah <jollys@xilinx.com>

Xilinx now requires the PMU FW when using ATF, so it doesn't make sense
to maintain checks for the PMU FW in ATF. This also means that cases
where ATF came up before the PMU FW (such as on QEMU) ATF will now hang
waiting for the PMU FW instead of aborting.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

Use positive logic (pm_up instead of pm_down) to check whether PMU
services are available. This change also puts the variable into the
BSS section rather than the Data section as the variable is now
initialized to 0 rather than 1.
Signed-off-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

If we can't find the FSBL handoff struct don't panic and just use the
defaults instead.

We still print a warning to the user to let them know what we couldn't
find it.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

Instead of calling panic() in fsbl_atf_handover() return the error
status so that bl31_early_platform_setup() can act accordingly.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Type "entry_point_info_t" is used in zynqmp_private.h. It is defined
in "bl_common.h". The header file which defines the type should be
included.
Signed-off-by: Wendy Liang <jliang@xilinx.com>

Added SHA to calculate SHA3 hash,RSA to encrypt data with
public key and decrypt with private key and AES to do symmetric
encryption with User key or device key.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Read ipdisable reg which needs to be used for cg/eg/ev device detection.
ATF runs in EL3 that's why this read can be done directly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Add new id codes for RFSoC's.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This patch corrects the SVD mask for getting chip ID
using 0xe is wrong and 0x7 is correct.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

psci system_reset and system_off calls now retrieve shutdown scope on
the fly. The default scope is system, but it can be changed by calling
pm_system_shutdown(2, scope)

Until full support for different restart scopes becomes available with
PSCI 1.1 this change allows users to set the reboot scope to match
their application needs.

Possible scope values:
0 - APU subsystem: does not affect RPU, PMU or PL
1 - PS only: shutdown/restart entire PS without affecting PL
2 - System: shutdown/restart applies to entire system
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Davorin Mista <davorin.mista@aggios.com>

The PM_INIT_FINALIZE PM API is required to inform the PFW that APU is
done with requesting nodes and that not-requested nodes can be powered
down. If PM is not enabled, this call will never be made and PFW will
never power down any of the nodes which APU can use.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>

Signed-off-by: Filip Drazic <filip.drazic@aggios.com>

This patch adds pm_secure_rsaaes() API to provide access to
the xilsecure library for loading secure images
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Read boot mode register using pm_mmio_read if pmu is
present otherwise access it directly using mmio_read_32().
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

The pm_req_wakeup PM API accepts start address (64-bit unsiged integer)
and a flag stating if address should be used. To save an argument
of the SMC call, flag is encoded in the LSB of the address, since
addresses are word aligned.
Decode start address and use-address flag in the PM SMC handler and
pass them to pm_req_wakeup.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>

Call to pm_client_wakeup from pm_req_wakeup prevented the PM API
call to be used to wake up non-APU processor (e.g. from higher ELs),
since it clears power down request for specified APU processor.
Move this function out of pm_client_wakeup to allow passing wake up
requests to the PMU for other processor in the system.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>

NODE_EXTERN is the slave node which represents an external wake
source.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>

Beside standard suspend-to-RAM state, Zynq MPSoC supports
suspend-to-RAM state with additional power savings, called
power-off suspend-to-RAM. If this mode is set, only NODE_EXTERN
must be set as wake source. Standard suspend-to-RAM procedure
is unchanged.

This patch adds support for setting suspend mode from higher
ELs and ensuring that all conditions for power-off suspend mode
are set.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>