GitLab

This patch adds to support the suspend/resume for rk3399 SoCs.
Signed-off-by: Shengfei xu <xsf@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This patch puts the definition of `plat_get_syscnt_freq()`
under `#ifdef ARM_SYS_CNTCTL_BASE` in arm_common.c file.
This is the fix for compilation error introduced by commit-id
`749ade45`, for platforms that use arm_common.c but do not
provide a memory mapped interface to the generic counter.

Fixes ARM-software/tf-issues#395

Change-Id: I2f2b10bd9500fa15308541ccb15829306a76a745

This patch has the following change for rk3399.

* Set the uart to 115200 since the loader decide to set
  uart baud to 115200Hz. So the ATF also should set uart baud to 115200.

* We need ensure the bl31 base is greater than 4KB since there are have
  the shared mem for coreboot.(Note: the previous vesion was tested with uboot)

Otherwise, we will happen the exception crash since the ddr area won't
to work from the shared ram address in some cases.

For example, the exception crash:
CBFS: Found @ offset 19c80 size 24074
exception _sync_sp_el0
ELR = 0x0000000000008000
ESR = 0x0000000002000000
SPSR = 0x600003cc
FAR = 0xffffffff00000000
SP = 0x00000000ff8ed230
...
X29 = 0x00000000ff8c1fc0
X30 = 0x000000000030e3b0
exception death

Change-Id: I8bc557c6bcaf6804d2a313b38667d3e2517881d7
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This patch moves the definition for `plat_get_syscnt_freq()`
from arm_bl31_setup.c to arm_common.c. This could be useful
in case a delay timer needs to be installed based on the
generic timer in other BLs.
This patch also modifies the return type for this function
from `uint64_t` to `unsigned long long` within ARM and other
platform files.

Change-Id: Iccdfa811948e660d4fdcaae60ad1d700e4eda80d

It is up to the platform to implement the new plat_crash_print_regs macro to
report all relevant platform registers helpful for troubleshooting.

plat_crash_print_regs merges or calls previously defined plat_print_gic_regs
and plat_print_interconnect_regs macros for each existing platforms.

NOTE: THIS COMMIT REQUIRES ALL PLATFORMS THAT ENABLE THE `CRASH_REPORTING`
BUILD FLAG TO MIGRATE TO USE THE NEW `plat_crash_print_regs()` MACRO. BY
DEFAULT, `CRASH_REPORTING` IS ENABLED IN DEBUG BUILDS FOR ALL PLATFORMS.

Fixes: arm-software/tf-issues#373
Signed-off-by: Gerald Lejeune <gerald.lejeune@st.com>

In mt8173, there are totally 10 non-cpu mtcmos, so we cannot tell
if SPM finished the power control flow by 10 status bits of PASR_PDP_3.
So, extend PASR_PDP_3 status bits from 10 to 20 so that we can
make sure if the control action has been done precisely.

Change-Id: Ifd4faaa4173c6e0543aa8471149adb9fe7fadedc
Signed-off-by: Fan Chen <fan.chen@mediatek.com>

This patch modifies the upstream platform port makefiles to use the new
xlat_tables library files. This patch also makes mmap region setup common
between AArch64 and AArch32 for FVP platform port. The file `fvp_common.c`
is moved from the `plat/arm/board/fvp/aarch64` folder to the parent folder
as it is not specific to AArch64.

Change-Id: Id2e9aac45e46227b6f83cccfd1e915404018ea0b

This patch fixes the compilation error in Rockchip rk3368 platform port when
it is built in release mode.

Fixes ARM-software/tf-issues#389

Change-Id: I1a3508ac3a620289cf700e79db8f08569331ac53

To avoid confusion the build option BL33_BASE has been renamed to
PRELOADED_BL33_BASE, which is more descriptive of what it does and
doesn't get mistaken by similar names like BL32_BASE that work in a
completely different way.

NOTE: PLATFORMS USING BUILD OPTION `BL33_BASE` MUST CHANGE TO THE NEW
BUILD OPTION `PRELOADED_BL33_BASE`.

Change-Id: I658925ebe95406edf0325f15aa1752e1782aa45b

The BL33 address is now set in arm_bl31_early_platform_setup() so
that the preloaded BL33 boot option is available when RESET_TO_BL31
is also used.

Change-Id: Iab93e3916f9199c3387886b055c7cd2315efed29

Previously, when building TF without SPD support, BL2 tried to load a
BL32 image from the FIP and fails to find one, which resulted on
warning messages on the console. Even if there is a BL32 image in the
FIP it shouldn't be loaded because there is no way to transfer
control to the Secure Payload without SPD support.

The Makefile has been modified to pass a define of the form
SPD_${SPD} to the source code the same way it's done for PLAT. The
define SPD_none is then used to undefine BL32_BASE when BL32 is not
used to prevent BL2 from trying to load a BL32 image and failing,
thus removing the warning messages mentioned above.

Fixes ARM-software/tf-issues#287

Change-Id: Ifeb6f1c26935efb76afd353fea88e87ba09e9658

To fix build errors in following build conditions,
DEBUG=1 LOG_LEVEL<40
DEBUG=0 LOG_LEVEL>=40

Change-Id: Ib34aed07b2ae0abd8a3a46948adc9fbeaae715aa
Signed-off-by: yt.lee <yt.lee@mediatek.com>

The Xilinx Zynq UltraScale+ MPSOC containes a quad A53 cluster. This
patch adds the platform port for that SoC.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

This patch adds to support the RK3368 and RK3399 SoCs.

RK3368/RK3399 is one of the Rockchip family SoCs, which is an
multi-cores ARM SoCs.

This patch adds support to boot the Trusted Firmware on RK3368/RK3399
SoCs, and adds support to boot secondary CPUs, enter/exit core
power states for all CPUs in the slow/fast clusters.

This is the initial version for rockchip SoCs.(RK3368/RK3399 and next SoCs)
* Support arm gicv2 & gicv3.
* Boot up multi-cores CPU.
* Add generic CPU helper functions.
* Support suspend/resume.
* Add system_off & system_reset implementation.
* Add delay timer platform implementation.
* Support the new porting interface for the PSCI implementation.

Change-Id: I704bb3532d65e8c70dbd99b512c5e6e440ea6f43
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Shengfei xu <xsf@rock-chips.com>

Make the timer configuration conditional on the optional interface being
available.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

This patch modifies the return type of the platform API
`plat_get_ns_image_entrypoint()` from `unsigned long` to
`uintptr_t` in accordance with the coding guidelines.

Change-Id: Icb4510ca98b706aa4d535fe27e203394184fb4ca

BL31 usually handles confidential stuff, its memory must not be
read/write accessible from non-secure world. This patch protects
the BL31 memory range from non-secure read/write access.

Change-Id: I442fb92b667bb2f9a62d471a90508b1ba4489911
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>

This patch adds support to program TrustZone protection on ARM platforms that
implement a DMC-500. arm_dmc_500.c has been added which implements the
arm_dmc_tzc_setup() function. This function relies on constants related to TZC
programming that are exported by each platform to program TrustZone protection
using the DMC-500 TrustZone controller driver. This function should be called
from plat_arm_security_setup() which is implemented by each platform.

Change-Id: I5400bdee9e4b29155fd11296a40693d512312f29

This patch migrates ARM Standard platforms to the refactored TZC driver.

Change-Id: I2a2f60b645f73e14d8f416740c4551cec87cb1fb

This patch adds support for non-volatile counter authentication to
the Authentication Module. This method consists of matching the
counter values provided in the certificates with the ones stored
in the platform. If the value from the certificate is lower than
the platform, the boot process is aborted. This mechanism protects
the system against rollback.

The TBBR CoT has been updated to include this method as part of the
authentication process. Two counters are used: one for the trusted
world images and another for the non trusted world images.

** NEW PLATFORM APIs (mandatory when TBB is enabled) **

int plat_get_nv_ctr(void *cookie, unsigned int *nv_ctr);

    This API returns the non-volatile counter value stored
    in the platform. The cookie in the first argument may be
    used to select the counter in case the platform provides
    more than one (i.e. TBSA compliant platforms must provide
    trusted and non-trusted counters). This cookie is specified
    in the CoT.

int plat_set_nv_ctr(void *cookie, unsigned int nv_ctr);

    This API sets a new counter value. The cookie may be
    used to select the counter to be updated.

An implementation of these new APIs for ARM platforms is also
provided. The values are obtained from the Trusted Non-Volatile
Counters peripheral. The cookie is used to pass the extension OID.
This OID may be interpreted by the platform to know which counter
must return. On Juno, The trusted and non-trusted counter values
have been tied to 31 and 223, respectively, and cannot be modified.

** IMPORTANT **

THIS PATCH BREAKS THE BUILD WHEN TRUSTED_BOARD_BOOT IS ENABLED. THE
NEW PLATFORM APIs INTRODUCED IN THIS PATCH MUST BE IMPLEMENTED IN
ORDER TO SUCCESSFULLY BUILD TF.

Change-Id: Ic943b76b25f2a37f490eaaab6d87b4a8b3cbc89a

This patch adds an option to the ARM common platforms to load BL31 in the
TZC secured DRAM instead of the default secure SRAM.

To enable this feature, set `ARM_BL31_IN_DRAM` to 1 in build options.
If TSP is present, then setting this option also sets the TSP location
to DRAM and ignores the `ARM_TSP_RAM_LOCATION` build flag.

To use this feature, BL2 platform code must map in the DRAM used by
BL31. The macro ARM_MAP_BL31_SEC_DRAM is provided for this purpose.
Currently, only the FVP BL2 platform code maps in this DRAM.

Change-Id: If5f7cc9deb569cfe68353a174d4caa48acd78d67

Added a new platform porting function plat_panic_handler, to allow
platforms to handle unexpected error situations. It must be
implemented in assembly as it may be called before the C environment
is initialized. A default implementation is provided, which simply
spins.

Corrected all dead loops in generic code to call this function
instead. This includes the dead loop that occurs at the end of the
call to panic().

All unnecesary wfis from bl32/tsp/aarch64/tsp_exceptions.S have
been removed.

Change-Id: I67cb85f6112fa8e77bd62f5718efcef4173d8134

This patch adds big core ARMPLL control in system suspend flow.

Change-Id: I27a45dbbb360f17ff0b524a125630358ee2277e2
Signed-off-by: Louis Yu <louis.yu@mediatek.com>
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>

We no longer need to control power signal via gpio during system off,
thus remove gpio driver support from platform code.

Change-Id: I6dfec129fa163330951f37b45b71ba5b90355c3b
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>

MT8173 platform code is incompatible with RESET_TO_BL31, add #error
directive to prevent the case.

We also move mt8173_def.h and plat_private.h to include directory, and
remove some unnecessary code.

Change-Id: I47b8d0a506820a4ea1fbe8c8fb0ec6c68d88feb5
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>

This patch fixes inconsistencies in bl1_tbbr_image_descs[]
and miscellaneous fixes in Firmware Update code.

Following are the changes:
* As part of the original FWU changes, a `copied_size`
  field was added to `image_info_t`. This was a subtle binary
  compatibility break because it changed the size of the
  `bl31_params_t` struct, which could cause problems if
  somebody used different versions of BL2 or BL31, one with
  the old `image_info_t` and one with the new version.
  This patch put the `copied_size` within the `image_desc_t`.
* EXECUTABLE flag is now stored in `ep_info.h.attr` in place
  of `image_info.h.attr`, associating it to an entrypoint.
* The `image_info.image_base` is only relevant for secure
  images that are copied from non-secure memory into secure
  memory. This patch removes initializing `image_base` for
  non secure images in the bl1_tbbr_image_descs[].
* A new macro `SET_STATIC_PARAM_HEAD` is added for populating
  bl1_tbbr_image_descs[].ep_info/image_info.h members statically.
  The version, image_type and image attributes are now
  populated using this new macro.
* Added PLAT_ARM_NVM_BASE and PLAT_ARM_NVM_SIZE to avoid direct
  usage of V2M_FLASH0_XXX in plat/arm/common/arm_bl1_fwu.c.
* Refactoring of code/macros related to SECURE and EXECUTABLE flags.

NOTE: PLATFORM PORTS THAT RELY ON THE SIZE OF `image_info_t`
      OR USE the "EXECUTABLE" BIT WITHIN `image_info_t.h.attr`
      OR USE THEIR OWN `image_desc_t` ARRAY IN BL1, MAY BE
      BROKEN BY THIS CHANGE. THIS IS CONSIDERED UNLIKELY.

Change-Id: Id4e5989af7bf0ed263d19d3751939da1169b561d

`board_arm_def.h` contains multiple definitions of
`PLAT_ARM_MMAP_ENTRIES` and `MAX_XLAT_TABLES` that are optimised for
memory usage depending upon the chosen build configuration. To ease
maintenance of these constants, this patch replaces their multiple
definitions with a single set of definitions that will work on all ARM
platforms.

Platforms can override the defaults with optimal values by enabling the
`ARM_BOARD_OPTIMISE_MMAP` build option. An example has been provided in
the Juno ADP port.

Additionally, `PLAT_ARM_MMAP_ENTRIES` is increased by one to accomodate
future ARM platforms.

Change-Id: I5ba6490fdd1e118cc9cc2d988ad7e9c38492b6f0

The common topology description helper funtions and macros for
ARM Standard platforms assumed a dual cluster system. This is not
flexible enough to scale to multi cluster platforms. This patch does
the following changes for more flexibility in defining topology:

1. The `plat_get_power_domain_tree_desc()` definition is moved from
   `arm_topology.c` to platform specific files, that is `fvp_topology.c`
   and `juno_topology.c`. Similarly the common definition of the porting
   macro `PLATFORM_CORE_COUNT` in `arm_def.h` is moved to platform
   specific `platform_def.h` header.

2. The ARM common layer porting macros which were dual cluster specific
   are now removed and a new macro PLAT_ARM_CLUSTER_COUNT is introduced
   which must be defined by each ARM standard platform.

3. A new mandatory ARM common layer porting API
   `plat_arm_get_cluster_core_count()` is introduced to enable the common
   implementation of `arm_check_mpidr()` to validate MPIDR.

4. For the FVP platforms, a new build option `FVP_NUM_CLUSTERS` has been
   introduced which allows the user to specify the cluster count to be
   used to build the topology tree within Trusted Firmare. This enables
   Trusted Firmware to be built for multi cluster FVP models.

Change-Id: Ie7a2e38e5661fe2fdb2c8fdf5641d2b2614c2b6b

The shared memory region on ARM platforms contains the mailboxes and,
on Juno, the payload area for communication with the SCP. This shared
memory may be configured as normal memory or device memory at build
time by setting the platform flag 'PLAT_ARM_SHARED_RAM_CACHED' (on
Juno, the value of this flag is defined by 'MHU_PAYLOAD_CACHED').
When set as normal memory, the platform port performs the corresponding
cache maintenance operations. From a functional point of view, this is
the equivalent of setting the shared memory as device memory, so there
is no need to maintain both options.

This patch removes the option to specify the shared memory as normal
memory on ARM platforms. Shared memory is always treated as device
memory. Cache maintenance operations are no longer needed and have
been replaced by data memory barriers to guarantee that payload and
MHU are accessed in the right order.

Change-Id: I7f958621d6a536dd4f0fa8768385eedc4295e79f

All files including plat/mediatek/mt8173/drivers/gpio/gpio.h were
using system includes instead of user includes, which may cause the
wrong version of the header to be included. Said includes have been
changed to user includes to make sure that the included file is the
wanted one.

Change-Id: I29bdfe96fbd9a7900875e2357bbb43f3ea431fa5

ARM Trusted Firmware supports 2 different interconnect peripheral
drivers: CCI and CCN. ARM platforms are implemented using either of the
interconnect peripherals.

This patch adds a layer of abstraction to help ARM platform ports to
choose the right interconnect driver and corresponding platform support.
This is as described below:

1. A set of ARM common functions have been implemented to initialise an
interconnect and for entering/exiting a cluster from coherency. These
functions are prefixed as "plat_arm_interconnect_". Weak definitions of
these functions have been provided for each type of driver.

2.`plat_print_interconnect_regs` macro used for printing CCI registers is
moved from a common arm_macros.S to cci_macros.S.

3. The `ARM_CONFIG_HAS_CCI` flag used in `arm_config_flags` structure
is renamed to `ARM_CONFIG_HAS_INTERCONNECT`.

Change-Id: I02f31184fbf79b784175892d5ce1161b65a0066c

Current code mandates loading of SCP_BL2/SCP_BL2U images for all
CSS platforms. On future ARM CSS platforms, the Application
Processor (AP) might not need to load these images. So, these
items can be removed from the FIP on those platforms.

BL2 tries to load  SCP_BL2/SCP_BL2U images if their base
addresses are defined causing boot error if the images are not
found in FIP.

This change adds a make flag `CSS_LOAD_SCP_IMAGES` which if set
to `1` does:
1. Adds SCP_BL2, SCP_BL2U images to FIP.
2. Defines the base addresses of these images so that AP loads
   them.

And vice-versa if it is set to `0`. The default value is set to
`1`.

Change-Id: I5abfe22d5dc1e9d80d7809acefc87b42a462204a

Prior to this patch, it was assumed that on all ARM platforms the bare
minimal security setup required is to program TrustZone protection. This
would always be done by programming the TZC-400 which was assumed to be
present in all ARM platforms. The weak definition of
platform_arm_security_setup() in plat/arm/common/arm_security.c
reflected these assumptions.

In reality, each ARM platform either decides at runtime whether
TrustZone protection needs to be programmed (e.g. FVPs) or performs
some security setup in addition to programming TrustZone protection
(e.g. NIC setup on Juno). As a result, the weak definition of
plat_arm_security_setup() is always overridden.

When a platform needs to program TrustZone protection and implements the
TZC-400 peripheral, it uses the arm_tzc_setup() function to do so. It is
also possible to program TrustZone protection through other peripherals
that include a TrustZone controller e.g. DMC-500. The programmer's
interface is slightly different across these various peripherals.

In order to satisfy the above requirements, this patch makes the
following changes to the way security setup is done on ARM platforms.

1. arm_security.c retains the definition of arm_tzc_setup() and has been
   renamed to arm_tzc400.c. This is to reflect the reliance on the
   TZC-400 peripheral to perform TrustZone programming. The new file is
   not automatically included in all platform ports through
   arm_common.mk. Each platform must include it explicitly in a platform
   specific makefile if needed.

   This approach enables introduction of similar library code to program
   TrustZone protection using a different peripheral. This code would be
   used by the subset of ARM platforms that implement this peripheral.

2. Due to #1 above, existing platforms which implements the TZC-400 have been
   updated to include the necessary files for both BL2, BL2U and BL31
   images.

Change-Id: I513c58f7a19fff2e9e9c3b95721592095bcb2735

Current code assumes `SCP_COM_SHARED_MEM_BASE` as the base address
for BOM/SCPI protocol between AP<->SCP on all CSS platforms. To
cater for future ARM platforms this is made platform specific.
Similarly, the bit shifts of `SCP_BOOT_CONFIG_ADDR` are also made
platform specific.

Change-Id: Ie8866c167abf0229a37b3c72576917f085c142e8

Functions to configure the MMU in S-EL1 and EL3 on ARM platforms
expect each platform to export its memory map in the `plat_arm_mmap`
data structure. This approach does not scale well in case the memory
map cannot be determined until runtime. To cater for this possibility,
this patch introduces the plat_arm_get_mmap() API. It returns a
reference to the `plat_arm_mmap` by default but can be overridden
by a platform if required.

Change-Id: Idae6ad8fdf40cdddcd8b992abc188455fa047c74

Each ARM Compute Subsystem based platform implements a System Security
Control (SSC) Registers Unit. The SSC_VERSION register inside it carries
information to identify the platform. This enables ARM Trusted Firmware
to compile in support for multiple ARM platforms and choose one at
runtime. This patch adds macros to enable access to this register.
Each platform is expected to export its PART_NUMBER separately.

Additionally, it also adds juno part number.

Change-Id: I2b1d5f5b65a9c7b76c6f64480cc7cf0aef019422

This patch moves the definition of some macros used only on
ARM platforms from common headers to platform specific headers.
It also forces all ARM standard platforms to have distinct
definitions (even if they are usually the same).
 1. `PLAT_ARM_TZC_BASE` and `PLAT_ARM_NSTIMER_FRAME_ID` have been
     moved from `css_def.h` to `platform_def.h`.
 2. `MHU_BASE` used in CSS platforms is moved from common css_def.h
    to platform specific header `platform_def.h` on Juno and
    renamed as `PLAT_ARM_MHU_BASE`.
 3. To cater for different sizes of BL images, new macros like
    `PLAT_ARM_MAX_BL31_SIZE` have been created for each BL image. All
    ARM platforms need to define them for each image.

Change-Id: I9255448bddfad734b387922aa9e68d2117338c3f

Replaced a long dash in a comment by the ASCII character '-'. Support
for multibyte character in the source character set is not enforced by
the C99 standard. To maximize compatibility with C processing tools
(e.g. compilers or static code analysis tools), they should be removed.

Change-Id: Ie318e380d3b44755109f042a76ebfd2229f42ae3

The debug prints used to debug translation table setup in xlat_tables.c
used the `printf()` standard library function instead of the stack
optimized `tf_printf()` API. DEBUG_XLAT_TABLE option was used to enable
debug logs within xlat_tables.c and it configured a much larger stack
size for the platform in case it was enabled. This patch modifies these
debug prints within xlat_tables.c to use tf_printf() and modifies the format
specifiers to be compatible with tf_printf(). The debug prints are now enabled
if the VERBOSE prints are enabled in Trusted Firmware via LOG_LEVEL build
option.

The much larger stack size definition when DEBUG_XLAT_TABLE is defined
is no longer required and the platform ports are modified to remove this
stack size definition.

Change-Id: I2f7d77ea12a04b827fa15e2adc3125b1175e4c23

We found sometimes mtcmos operation is too long in spm (>1ms),
so update a new version to fix it.
I verified with 5 hours power_LoadTest, every mtcmos control
can finish in 500us (average is 100~200us).

Change-Id: I47b712bf9898870f4abcecbea47e01b9786231d4
Signed-off-by: Fan Chen <fan.chen@mediatek.com>