GitLab

This patch adds memory barriers to the trampoline code copying TZDRAM
contents to SysRAM during exit from System Suspend. These barriers
make sure that all the copies go through before we start executing in
SysRAM.

Reported by: Nathan Tuck <ntuck@nvidia.com>

Change-Id: I3fd2964086b6c0e044cc4165051a4801440db9cd
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The Memory Controller provides a control register to check
if the video memory can be resized. The previous bootloader
might have locked this feature, which will be reflected by
this register.

This patch reads the control register before processing
a video memory resize request. An error code, -ENOTSUP,
is returned if the feature is locked.

Change-Id: Ia1d67f7a94aa15c6b18ff5c9b9b952e179596ae3
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>

MMIO writes should verify that the writes actually went through.
Read the value back after the write operation, perform assert
if the read back value is not same as the write value.

Change-Id: Id2ceb014116f3aa6a9e86505ca1ae9911470a679
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>

This patch removes the unused cortex_a53.h header file from
common Tegra files.

This change fixes the violation of CERTC Rule: DCL23.

Change-Id: Iaf7c34cc6323b78028258e188c00724c52afba85
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

During boot the platform enables dual execution for Xavier CPUs.
This patch reads back the ACTLR_ELx register to verify that the bit
is actually set. It asserts if the bit is not set.

Change-Id: I5ba9491ced86285d307b95efa647a427ff77c79e
Signed-off-by: Kalyani Chidambaram Vaidyanathan <kalyanic@nvidia.com>

The firewall settings for the hardware resources are present in the
Security Configuration Registers. The firewall settings are programmed
by other software components and so must be verified for correctness
before touching the hardware resources they protect.

This patch reads the firewall settings during early boot and asserts
if the settings mismatch.

Change-Id: I53cc9aeadad32e54e460db0fa2c38e46bcc92066
Signed-off-by: Kalyani Chidambaram Vaidyanathan <kalyanic@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

With an open source SPMI driver we can now remove qtiseclib involvement
in reset and shutdown handling by setting the required registers
directly.

Change-Id: I6bf1db15734048df583daa2a4ee98701c6ece621
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch adds a very rudimentary driver for the SPMI arbitrator used
to access the PMIC. It doesn't support all the controller's actual
arbitration features, so it should probably not be used concurrently
with a running kernel (and it's also not optimized for performance). But
it can be used to set a few registers during boot or on shutdown to
control reset handling, which is all we need it for.

Change-Id: I8631c34a2a89ac71aa1ec9b8266e818c922fe34a
Signed-off-by: Julius Werner <jwerner@chromium.org>

The patch adding platform support for sc7180 landed around roughly the
same time as the patch that changed GICV3_IMPL to GICV3_SUPPORT_GIC600.
Thus the sc7180 Makefile is still using the old variable name which now
no longer does anything, and it hangs on boot due to the lacking GIC-600
support. This patch fixes the issue.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id76ada1445c3c5ac9a5a3697b4e749088b89d796

This patch introduces the following changes to enable
compilation for `SPD=spmd` command line option.

* compile plat_spmd_manifest.c
* compile libfdt source files

Verified with the `SPD=spmd` command line option for
Tegra194 platforms.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I7f57aa4f1756b19f78d87415bb80794417174bc8

This patch includes the following files from libc to
compile libfdt:

* memchr.c
* memcmp.c
* strrchr.c

The BUILD_PLAT macro is evaluated earlier to allow libfdt
installation to the right directory.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: Ie43fcf701dc051670e6372e21b3a84a6416c1735

libfdt does not support the -Wsign-compare compiler option
and the right patch will eventually be pushed upstream.

This patch disables the -Wsign-compare compiler option
to allow libfdt compilation for Tegra platforms until
the actual issue is fixed.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: Ib7a93946cad1ea9ec1b46751edb79a74c08ed0ac

This patch includes the bl_common.h from plat_spmd_manifest.c to
fix the following compilation errors

<snip>
plat/common/plat_spmd_manifest.c: In function 'plat_spm_core_manifest_load':
plat/common/plat_spmd_manifest.c:130:18: error: implicit declaration of function 'page_align' [-Werror=implicit-function-declaration]
  130 |  pm_base_align = page_align(pm_base, UP);
      |                  ^~~~~~~~~~
plat/common/plat_spmd_manifest.c:130:38: error: 'UP' undeclared (first use in this function); did you mean 'UL'?
  130 |  pm_base_align = page_align(pm_base, UP);
      |                                      ^~
      |                                      UL
plat/common/plat_spmd_manifest.c:130:38: note: each undeclared identifier is reported only once for each function it appears in
plat/common/plat_spmd_manifest.c:146:38: error: 'DOWN' undeclared (first use in this function)
  146 |  pm_base_align = page_align(pm_base, DOWN);
      |                                      ^~~~
cc1: all warnings being treated as errors
<snip>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: Ib8edb36c6a80a23df2462e708c513c966aab1fef

This patch removes the unused interrupt mapping for AON_WDT
for all Tegra194 platforms.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I475a1e83f809c740e62464b5b4e93cb0a2e33d6b

The SMMU configuration can get corrupted or updated by
external clients during boot without our knowledge.

This patch introduces a "verify" function for the SMMU
driver, to check that the boot configuration settings are
intact.  Usually, this function should be called at the
end of the boot cycle.

This function only calls panic() on silicon platforms.

Change-Id: I2ab45a7f228781e71c73ba1f4ffc49353effe146
Signed-off-by: George Bauernschmidt <georgeb@nvidia.com>

TZDRAM setup is not required for all Tegra SoCs. The previous bootloader
can enable the TZDRAM fence due to architectural improvements in the
newer chips.

This patch moves the TZDRAM setup to early_boot handlers for SoCs to
handle this scenario.

Change-Id: I6481b4f848a4dadc20cb83852cd8e19a242b3a34
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes the deprecated 'plat_core_pos_by_mpidr' function
from the Tegra platform port.

Change-Id: I32e06cb7269e4fbfaf9ad6c26d0722201f982f9e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The GICC interface exists only on the interrupt controllers following
the GICv2 specification.

This patch prints the GICC register contents from the platform's macro,
plat_crash_print_regs' only when TEGRA_GICC_BASE is defined. This
allows platforms using future versions of the GIC specification to
still use this macro.

Change-Id: Ia5762d0a1ae28c832664d69362a7776e46a22ad1
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

SPE no longer requires the flush bit to be set to start transmitting
characters over the physical uart. Therefore, the flush bit is no
longer required when calling console_core_putc. However, flushing the
console still requires the flush bit.

This patch removes the flush bit from the mailbox messages in
console_core_putc to improve ACK latency.

Original change by: Mustafa Bilgen <mbilgen@nvidia.com>

Change-Id: I5b7d1f3ea69ea2ce308566dbaae222b04e4c373d
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch verifies that the binary image is compatible with
chip ID of the platform.

Change-Id: I28db221b4442aa8827a092faadf32f110d7c5cb4
Signed-off-by: kalyanic <kalyanic@nvidia.com>

Allocated 512-959 SPI numbers for remote n1sdp chip and same has been
referenced for GIC routing table.

Change-Id: Id79ea493fd665ed93fe9644a59e363ec10441098
Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com>

This reverts commit e7d344de.
 This reverts the patch https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/5313 due to a timing issue with the merge.  The merge occurred at the same time as the additional comments and thusly were were not seen until the merge was done.  This reverts the change and additional patches from Alexei will follow to address the concerns expressed in the orignal patch.

Change-Id: Iae5f6403c93ac13ceeda29463883fcd4c437f2b7

Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: Icf90c2ccce75257908ba3d4703926041d64b1dd3

CPU hotplug & cpuidle have some race condition when doing CPU hotplug
stress test. different CPU cores have the chance to access the same
GPC register(A53_AD), so lock is necessary to do exlusive access.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Change-Id: I1296592e05fa78429c3f0fac066951521db755e3

Trace analysis of FVP_Base_AEMv8A model running in
Aarch32 mode with the build options listed below:
TRUSTED_BOARD_BOOT=1 GENERATE_COT=1
ARM_ROTPK_LOCATION=devel_ecdsa KEY_ALG=ecdsa
ROT_KEY=plat/arm/board/common/rotpk/arm_rotprivk_ecdsa.pem
shows that when auth_signature() gets called
71.84% of CPU execution time is spent in memset() function
written in C using single byte write operations,
see lib\libc\memset.c.
This patch replaces C memset() implementation with assembler
version giving the following results:
- for Aarch32 in auth_signature() call memset() CPU time
reduced to 24.84%.
- Number of CPU instructions executed during TF-A
boot stage before start of BL33 in RELEASE builds:
----------------------------------------------
|  Arch   |     C      |  assembler |    %   |
----------------------------------------------
| Aarch32 | 2073275460 | 1487400003 | -28.25 |
| Aarch64 | 2056807158 | 1244898303 | -39.47 |
----------------------------------------------
The patch also replaces memset.c with aarch64/memset.S
in plat\nvidia\tegra\platform.mk.

Change-Id: Ifbf085a2f577a25491e2d28446ee95a4ac891597
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Add information about the third partition so it can be loaded into SPM
when running the tests
Signed-off-by: Ruari Phipps <ruari.phipps@arm.com>
Change-Id: I5544e88df391ef294ddf6b5750d468d3e74892b1

The number of gpc imr mask reg & the offset is different
on some SOC, so correct it & replace the magic number with
macro define.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Change-Id: Ic701675cdd92e043dcd7f06722f2e871068aec74

Keep A53 PLAT(SCU) power domain on in wait mode(ret).
RBC count only need to be set in PLAT OFF mode, so
change it accordingly.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Change-Id: Ie55e25c8210d298506fc4dca7a9653583db45e0c

This patch adds tegra_chipid_is_t194() function to check if it is a
Tegra 194 chip.

Change-Id: I6da6d3a2c9676b748931e42fde1b174cbcb4fd40
Signed-off-by: David Pu <dpu@nvidia.com>

This patch makes Tegra platform psci ops routines to static. These
routines are called by PSCI framework and no external linkage is
necessary. This patch also fixes MISRA C-2012 Rule 8.6 violations.

Change-Id: Idd2381809f76dc0fd578c1c92c0f8eea124f2e88
Signed-off-by: David Pu <dpu@nvidia.com>

Enable the spm_mm framework for the qemu_sbsa platform.
Memory layout required for spm_mm is created in secure SRAM.
Co-developed-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Change-Id: I104a623e8bc1e44d035b95f014a13b3f8b33a62a

In case of AT speculative workaround applied, page table walk
is disabled for lower ELs (EL1 and EL0) in EL3.
Hence added a wrapper function which temporarily enables page
table walk to execute AT instruction for lower ELs and then
disables page table walk.

Execute AT instructions directly for lower ELs (EL1 and EL0)
assuming page table walk is enabled always when AT speculative
workaround is not applied.

Change-Id: I4ad4c0bcbb761448af257e9f72ae979473c0dde8
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

Implemented platform functions to retrieve the soc-id information
for juno platform

Change-Id: Ie677120710b45e202a2d63a954459ece8a64b353
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

Implemented platform functions to retrieve the soc-id information
for FVP platform.

Change-Id: Id3df02ab290a210310e8d34ec9d706a59d817517
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

Removed common code for soc-id feature which is applicable
for all arm platforms.

In subsequent patches, added a platform based functions
for FVP and Juno to retrieve the soc-id information.

Change-Id: Idb632a935758a6caff2ca03a6eab8f663da8a93a
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

Fixed build failure due to the commit:905f93c7

 by removing
the inclusion of non-existent 'stdinit.h' file.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I8e3ca69c016b7a2354c58c4d384a492631c36286

SP804 TIMER is not platform specific, and current code base adds
multiple defines to use this driver. Like FVP_USE_SP804_TIMER and
FVP_VE_USE_SP804_TIMER.

This patch removes platform specific build flag and adds generic
flag `USE_SP804_TIMER` to be set to 1 by platform if needed.

Change-Id: I5ab792c189885fd1b98ddd187f3a38ebdd0baba2
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

Compiling BL31 for the Allwinner platform now produces a message about
the deprecation of gic_common.c.
Follow the advice and use include gicv2.mk instead.

Collect all includes at the beginning of the file on the way.

Change-Id: Iee46e21a630bfa831d28059f09aa7b049eb554bb
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Include the GICv2 makefile in STM32MP1 SP_min makefile, and use
${GICV2_SOURCES} instead of taking drivers/arm/gic files directly.

Change-Id: Ibcaed5b0bd17f6d8cf200e208c11cc10cd6d2ee5
Signed-off-by: Yann Gautier <yann.gautier@st.com>

For supporting dualroot CoT for Secure Partitions a new optional field
"owner" is introduced which will be used to sign the SP with
corresponding signing domain. To demonstrate its usage, this patch adds
owners to cactus Secure Partitions.
Signed-off-by: Ruari Phipps <ruari.phipps@arm.com>
Change-Id: I7b760580355fc92edf5402cecc38c38125dc1cae