GitLab

debug.S was using macros defined in debug.h, but since it didn't
include it, these macros were taking the value 0, which means that
all the preprocessor conditionals were wrong.

Change-Id: If4ca81cc5a1662991589f914a2557ceff0eaaede
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

qemu/optee: load OP-TEE pageable part 2MB above OP-TEE image

qemu: fix holding pen mailbox sequence

OP-TEE dedicates the end of the Qemu secure DRAM as specific out-of-TEE
secure RAM. To support this configuration the trusted firmware should
not load OP-TEE resources in this area.

To overcome the issue, OP-TEE pageable image is now loaded 2MByte above
the secure RAM base address.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

qemu: Add support for Trusted Board Boot

This patch adds support for TBB to qemu. An RSA ROT keypair is generated at
build time and is included into BL1/BL2. The key and content certificates
are read over semihosting.

Fixes ARM-software/tf-issues#526
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>

Before this change, plat_secondary_cold_boot_setup reads wake up mailbox
as a byte array but through 64bit accesses on unaligned 64bit addresses.
In the other hand qemu_pwr_domain_on wakes secondary cores by writing
into a 64bit array.

This change forces the 64bit mailbox format as PLAT_QEMU_HOLD_ENTRY_SIZE
explicitly specifies it.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Fix edmac

Publish and Subscribe framework

This allows other EL3 components to subscribe to CPU on events.

Update Firmware Design guide to list psci_cpu_on_finish as an available
event.

Change-Id: Ida774afe0f9cdce4021933fcc33a9527ba7aaae2
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This light-weight framework enables some EL3 components to publish
events which other EL3 components can subscribe to. Publisher can
optionally pass opaque data for subscribers. The order in which
subscribers are called is not defined.

Firmware design updated.

Change-Id: I24a3a70b2b1dedcb1f73cf48313818aebf75ebb6
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Migrate upstream platforms to using interrupt properties

New GIC APIs and specifying interrupt propertes

fiptool: Enable Visual Studio build

Add APIs to get and modify attributes of memory regions

uniphier: fix section of  ROTPK hash

Update Foundation, AEM and Cortex Models versions

Fix use of MSR (immediate)

Trusted Firmware has been tested as part of its CI system against Cortex
and Foundation models in the 11.1 Model release available on
developer.arm.com. Trusted Firmware has also been tested against the
v8.7 AEM model.  This patch updates the user guide documentation to
reflect the version of the Foundation, AEM and Cortex Models that
Trusted Firmware has been tested against.

Change-Id: Ia0f51469032427b6056567d151bf8144a7cf0e42
Signed-off-by: Eleanor Bonnici <Eleanor.bonnici@arm.com>

This is not executable code.  It should be put into .rodata instead
of .text section.

This produces more correct BL1 image when SEPARATE_CODE_AND_RODATA is
defined.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Make RTC out of reset mode since it may be used in UEFI.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Init EDMA controller with non secure mode. A lot of peripherals are
depend on EDMA controller. But EDMA controller is in secure mode
by default. And this operation has to be executed in secure mode.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

docs: Update Trusted Board Boot Requirements document number

Change-Id: Ia8503d446cc8b4246013046f6294fea364c9c882
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Change-Id: I1463a4f9b74d74d59ac1d37b7b9c8e53416ab904
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Change-Id: Ibca6ea29be32783de666e0e0a0481668fc11860f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Init and save / restore of PMCR_EL0 / PMCR

Update PSCI to v1.1

Updates are required to enable the fiptool utility to be built on a
Windows platform.  This change modifies the source files to enable
building with Visual Studio (detected via preprocessor settings).
The primary changes are:
  1.  Provide an implementation of the getopt_long function.  This does
      not exist in the Visual Studio CRT libraries because Windows
      commands normally use '/' not '-' as an option indicator.
  2.  Redirect some function names to match those supported by the
      Visual Studio libraries (when building with Visual Studio).
  2.  Modify a structure name (stat) to match that provided
      by the Visual Studio libraries (_stat).

Note - this change does not provide makefile updates.  It only modifies
       the sources to enable the fiptool to be built from a Visual
       Studio project.  In normal use the presence of FIPTOOL.EXE is
       enough to satisfy the make requirements.  A makefile change may
       be derived from the Visual Studio command line information at
       some point in the future.

Change-Id: I3ade77ea140246af3c030920b3f97c070087f111
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>

The implementation is the same as those used to disable it in EL3.

Change-Id: Ibfe7e69034a691fbf57477c5a76a8cdca28f6b26
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduces a new API in the translation tables library
(v2), that allows to change the memory attributes of a memory
region. It may be used to change its execution permissions and
data access permissions.

As a prerequisite, the memory must be already mapped. Moreover, it
must be mapped at the finest granularity (currently 4 KB).

Change-Id: I242a8c6f0f3ef2b0a81a61e28706540462faca3c
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduces a new API in the translation tables library
(v2), that allows to query the memory attributes of a memory block
or a memory page.

Change-Id: I45a8b39a53da39e7617cbac4bff5658dc1b20a11
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Previously, in AArch32, `IMAGE_XLAT_DEFAULT_REGIME` wasn't defined. The
translation regime is only used in the AArch64 port of the translation
tables library v2, so this is not a problem for now, but future patches
will use it.

`IMAGE_EL` isn't used in AArch32, so it isn't needed to define it.

Change-Id: I4acdb01a58658956ab94bd82ed5b7fee1aa6ba90
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The GIC driver initialization currently allows an array of interrupts to
be configured as secure. Future use cases would require more interrupt
configuration other than just security, such as priority.

This patch introduces a new interrupt property array as part of both
GICv2 and GICv3 driver data. The platform can populate the array with
interrupt numbers and respective properties. The corresponding driver
initialization iterates through the array, and applies interrupt
configuration as required.

This capability, and the current way of supplying array (or arrays, in
case of GICv3) of secure interrupts, are however mutually exclusive.
Henceforth, the platform should supply either:

  - A list of interrupts to be mapped as secure (the current way).
    Platforms that do this will continue working as they were. With this
    patch, this scheme is deprecated.

  - A list of interrupt properties (properties include interrupt group).
    Individual interrupt properties are specified via. descriptors of
    type 'interrupt_prop_desc_t', which can be populated with the macro
    INTR_PROP_DESC().

A run time assert checks that the platform doesn't specify both.

Henceforth the old scheme of providing list of secure interrupts is
deprecated. When built with ERROR_DEPRECATED=1, GIC drivers will require
that the interrupt properties are supplied instead of an array of secure
interrupts.

Add a section to firmware design about configuring secure interrupts.

Fixes ARM-software/tf-issues#262

Change-Id: I8eec29e72eb69dbb6bce77879febf32c95376942
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Change-Id: I795ec540942130b5ddc0fa1fd7167f7e1d1ae967
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The helpers perform read-modify-write on GIC*_ICFGR registers, but don't
serialise callers. Any serialisation must be taken care of by the
callers.

Change-Id: I71995f82ff2c7f70d37af0ede30d6ee18682fd3f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.

This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms.  The
deprecated interrupt list definitions are however retained to support
legacy builds.

Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.

NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.

Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I40feec1fe67a960d035061b54dd55610bc34ce1d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I14e33cfc7dfa93257c82d76fae186b17a1b6d266
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

SPIs can be routed to either a specific PE, or to any one of all
available PEs.

API documentation updated.

Change-Id: I28675f634568aaf4ea1aa8aa7ebf25b419a963ed
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>