GitLab

This removes the space allocation for the unused PHY register space.
For instance in PHY registers 0-127, only 0-90 are used, so don't save
the 91-127 registers. This saves about 1.6KB of space.

Change-Id: I0c9f6d9bed8f0c1f3b8b805dfb10cf0c06208919
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

the function pmu_cpuon_entrypoint() need to run in the pmusram,
we just copy bin file to pmusram before, now we add pmusram section
and link pmu_cpuon_entrypoint() to pmusram directly

Change-Id: Iae31e4c01c480c8e6f565a8f588332b478efdb16
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

The differential signal of DQS need keep low level
before gate training. It need enable RPULL and disable
PHY side ODT to ensure it when do gate training.
But it can not access the PHY registers to do it when
perform DFS.So the workaroud as below: It is ensure that
the PHY's read gate is landing somewhere in the incoming
DQS's pulses before it starts searching for pre-amble window.
It need get the rddqs_delay_ps to calculate the start point
of gate training for DFS.

Change-Id: I79eabcf4ec9a9c8f4539f68a51f22afba49c72fe
Signed-off-by: Lin Huang <hl@rock-chips.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

The printf() isn't used by the firmware itself, just by the tools under
the ./tools/ folder. Then tf_printf will unconditionally print.
Remove the unused print_dram_status_info() function.

Change-Id: Ie699ccb54a5be9a2cbbd7b8d4193b57075a2f57a
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

Remove struct rockchip_pm_ops_cb and instead of using weak functions
implement; in this way we want the codes look clear and simple;

Change-Id: Ib9e8a5e932fdfc2b3e6a1ec502c40dfe720ac400
Signed-off-by: tony.xie <tony.xie@rock-chips.com>

Sorry to miss the security configuration for SRAM, if we don't support
it, somebody may modify the comment of SRAM in the non-secure space.
Let's fix this issue.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This fixes code that set a tFC value in a register using the tRFC
value instead.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The F1 CAS latency setting was not bit shifted, which resulted in
setting the DRAM additive latency value instead.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

On resume, we use the DFS hardware to switch frequency index,
followed by a full training sequence on that index. Leaving
the DFS training modules enabled causes issues with the full
training done at resume. We also only needs these enabled
during a call to ddr_set_rate during runtime, so there's no
issue disabling them at the end of ddr_set_rate.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This moves the setting of the DQS drive strength to the M0 to minimize
the impact on DDR transactions. We need to have the DQS drive strength
changed for data training, which is triggered by the M0, but it also
needs to be changed back when data training is finished.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes an optimization to not recalculate parameters if the
frequency index being switched to hold the next frequency. This is
because some registers do not have a copy per frequency index, so this
optimization might be causing problems.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

We were getting far off values on resume for the RX_CAL_DQS values.
This saves and restores the values for suspend/resume until the root
of the problem is figured out
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

These macros were accidentally deleted in a previous cleanup. This
slipped through because the code using them is currently unused, but
that may change in the future.
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch shuffles the M0 Makefile flags around a bit trying to make
their purpose clearer and remove duplication. Since all three build
steps (compiling, assembling, linking) actually call GCC, remove the
misleading aliases $(AS) and $(LD) to avoid confusion that those tools
might be called directly. Split flags into a common group that has
meaning for all three steps and separate variables specific to each
step. Remove -nostartfiles which is a strict subset of -nostdlib.

Also add explicit parameters for -mfloat-abi=soft, -fomit-frame-pointer
and -fno-common. If omitted these settings depend on the toolchain's
built-in default and cause various problems if they resolve to
unexpected values.
Signed-off-by: Julius Werner <jwerner@chromium.org>

The goal is that make clear the secure and SoC codes. Now cleaning them
will help secure code extensions for RK3399 in the future.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

Move the BL31 loaded base address 0x10000 to 0x1000, and configure
the the memory range 0~1MB is secure, the goal is that make sure
the BL31 image will be not modified.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

So far, there are more and more features are supported on the RK3399,
meanwhile, these features are increasingly being defined and intertwined.
It's time to clean up and make them clearer.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This removes waiting for vblank on the M0 during ddrfreq transitions.
That will now be done in the kernel to allow scheduling to be done on
the CPU core that changes the ddr frequency. Waiting for vblank in
the M0 would have the CPU core that waits on the M0 spin looping for
up to 16ms (1 frame for the display).
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

we will set PMU_CRU_GATEDIS_CON0 when idle port, it will enable
all clock, for save power consumption, we need to restore old value
when finish it.
Signed-off-by: Lin Huang <hl@rock-chips.com>

As rk3399 TRM1.1 document show, when set PMU_CRU_GATEDIS_CON0/1
register, it need set the write_mask bit (bit16 ~ bit31), but as
we test, it not need it. So need to correct the setting way, otherwise
it will set wrong value to this register.
Signed-off-by: Lin Huang <hl@rock-chips.com>

We found that the DUT will be hanged if we don't set the bit_1 of the
PMUCRU_GATEDIS_CON0. But, from the TRM, there is weird that the bit_1
is set the clk_center1_gating_dis, not clk_pmum0_gating_dis. Is the
TRM incorrect? We need to check it with the IC team and re-clean the
commit message and explain it tomorrow.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This patch do following things:
1. Request hresetn_cm0s_pmu_req first then request
   poresetn_cm0s_pmu_req during M0 enable.
2. Do not diable M0 clock for ddr dvfs.
3. Correct the clk_pmum0_gating_dis bit, it is BIT0 not BIT1
4. do not set/clear hclk_noc_pmu_en in M0 code, it does not relate
   to the M0 clock.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

When vop is disabled and we read the vop register the system will
hang, so check vop status when we wait for the DMA finish flag to
avoid this sitiuation. This is done by checking for standby, DMA stop
mode, and disabled window states. Any one of these will prevent the
DMA finish flag from triggering.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

There is system timer in m0, we can use it to implement a set of
stopwatch functions for measuring timeouts.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The phy pll needs to get 2X frequency to the DDR, so set the
pll_postdiv to 0.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

For ddr dfs stable, We need to enable ddr CA training
when do ddr dfs.
Signed-off-by: Lin Huang <hl@rock-chips.com>

This fixes a hang with setting the DRAM rate based on a race condition
with the M0 which sets the DRAM rate. The AP can also starve the M0,
so this also delays the AP reads to the DONE parameter for the M0.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This enables per CS training at 666MHz and above for ddrfreq per
vendor recommendation. Since the threshold was used for latency was
the same value, this also adds a new value for that.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This patch sets the frequency configuration of the next DRAM DFS index
to the configuration of the current index. This does not perform a
frequency transition. It just configures registers so the training on
resume for both indices will be correct.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

We used dcf do ddr frequency scaling, but we just include a dcf
binary, it hard to maintain later, we have M0 compile flow in ATF,
and M0 can also work for ddr frequency scaling, so let's use it.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

Since the ATF project, we usually use the mmio_read_32 and
mmio_write_32. And the mmio_write_32, the firse parameter
is ADDR, the second is VALUE. In order to style consistency:

1/ rename readl/writel to mmio_read_32/mmio_write_32
2/ for keeping the same with mmio_write_32 in the ATF project,
   swap the order of the parameters for M0 mmio_write_32
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Lin Huang <hl@rock-chips.com>

when dram frequency below 260MHz, phy master dll may unlock, so
let phy master dll working at dll bypass mode when frequency is
below 260MHz.
Signed-off-by: Lin Huang <hl@rock-chips.com>

we can reuse the dram config from loader, so we can remove dram_init()
and dts_timing_receive() funciton in dram.c, add the dram_set_odt_pd()
function to get the odt and auto power down parameter from kernel.

This also removes the dcf_code_init function to allow the system to
actually boot.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

Replace all use of memset by zeromem when zeroing moderately-sized
structure by applying the following transformation:
memset(x, 0, sizeof(x)) => zeromem(x, sizeof(x))

As the Trusted Firmware is compiled with -ffreestanding, it forbids the
compiler from using __builtin_memset and forces it to generate calls to
the slow memset implementation. Zeromem is a near drop in replacement
for this use case, with a more efficient implementation on both AArch32
and AArch64.

Change-Id: Ia7f3a90e888b96d056881be09f0b4d65b41aa79e
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

We are duplicating this macro define, and it is useful enough
to be placed in the common place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Depending on the compiler used, it might try to link in libc even though
it's not required. Stop it from doing that.
Signed-off-by: Patrick Georgi <pgeorgi@google.com>

Some files have incorrect copyright notices, this patch fixes all
files with deviations from the standard notice.

Change-Id: I66b73e78a50a235acb55f1e2ec2052a42c0570d2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Commit b91d935f
("Add CFI debug frame information for ASM functions") modifies the
assembly macros 'func' and 'endfunc' to include CFI debug frame
information.

The rockchip platform uses a custom version of the 'func' macro with the
common 'endfunc' macro. The custom macro wasn't updated in
b91d935f resulting in the following
build error:
  plat/rockchip/rk3399/drivers/pmu/plat_pmu_macros.S: Assembler messages:
  plat/rockchip/rk3399/drivers/pmu/plat_pmu_macros.S:155: Error: .cfi_endproc without corresponding .cfi_startproc
  Makefile:532: recipe for target 'build/rk3399/release/bl31/plat_helpers.o' failed
  make: *** [build/rk3399/release/bl31/plat_helpers.o] Error 1

Fixing this by updating the sram_func macro in the rk3399 port.

Fixes: b91d935f

 ("Add CFI debug frame information for ASM functions")
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

We have do something for clocks gate.

Fox example as the below:
susped:
clk_gate_con_save();
clk_gate_con_disable();

resume:
clk_gate_con_restore();
--

SO, add the plls_suspend_prepare() and plls_resume_finish() are not
necessary to S2R, that will save S2R time if remove them.

BRANCH=none
BUG=chrome-os-partner:58870,chrome-os-partner:55934
TEST=build kevin, two dogfooders with suspend_stress_test
passing 3000 cycles and still going on.

Change-Id: Icfbabc0b3ea8d2b5108d4f3de99a803b6d459669
Signed-off-by: Caesar Wang <wxt@rock-chips.com>