GitLab

Add support for Marvell Armada-3700 COMPHY driver
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Some of COMPHY parameters depends on the hw connection between the SoC
and the PHY, which can vary on different boards e.g. due to different
wires length. Define the "porting layer" with some defaults
parameters. It ease updating static values which needs to be updated due
to board differences, which are now grouped in one place.

Example porting layer for a8k-db is under:
plat/marvell/a8k/a80x0/board/phy-porting-layer.h

If for some boards parameters are not defined (missing
phy-porting-layer.h), the default values are used
(drivers/marvell/comphy/phy-default-porting-layer.h)
and the following compilation warning is show:
"Using default comphy params - you may need to suit them to your board".

The common COMPHY driver code is extracted in order to be shared with
future COMPHY driver for A3700 SoC platforms
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

 - ddr
 - pfc [pin function controller]
 - qos [bandwidth]

checkpatch.pl is generating too many errors.

Reference code:
==============

rar_gen3: IPL and Secure Monitor Rev1.0.22
https://github.com/renesas-rcar/arm-trusted-firmware [rcar_gen3]

Author: Takuya Sakata <takuya.sakata.wz@bp.renesas.com>
Date:   Thu Aug 30 21:26:41 2018 +0900
	Update IPL and Secure Monitor Rev1.0.22

General Information:
===================

This port has been tested on the Salvator-X Soc_id r8a7795 revision
ES1.1 (uses an SPD).

Build Tested:
-------------
ATFW_OPT="LSI=H3 RCAR_DRAM_SPLIT=1 RCAR_LOSSY_ENABLE=1"
MBEDTLS_DIR=$mbedtls

$ make clean bl2 bl31 rcar PLAT=rcar ${ATFW_OPT} SPD=opteed

Other dependencies:
------------------
* mbed_tls:
  git@github.com:ARMmbed/mbedtls.git [devel]

  Merge: 68dbc94 f34a4c1
  Author: Simon Butcher <simon.butcher@arm.com>
  Date:   Thu Aug 30 00:57:28 2018 +0100

* optee_os:
  https://github.com/BayLibre/optee_os



  Until it gets merged into OP-TEE, the port requires Renesas' Trusted
  Environment with a modification to support power management.

  Author: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
  Date:   Thu Aug 30 16:49:49 2018 +0200
    plat-rcar: cpu-suspend: handle the power level
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>

* u-boot:
  The port has beent tested using mainline uboot.

  Author: Fabio Estevam <festevam@gmail.com>
  Date:   Tue Sep 4 10:23:12 2018 -0300

*linux:
  The port has beent tested using mainline kernel.

  Author: Linus Torvalds <torvalds@linux-foundation.org>
  Date:   Sun Sep 16 11:52:37 2018 -0700
      Linux 4.19-rc4

Overview
---------

BOOTROM starts the cpu at EL3; In this port BL2 will therefore be entered
at this exception level (the Renesas' ATF reference tree [1] resets into
EL1 before entering BL2 - see its bl2.ld.S)

BL2 initializes DDR (and i2c to talk to the PMIC on some platforms)
before determining the boot reason (cold or warm).

During suspend all CPUs are switched off and the DDR is put in
backup mode (some kind of self-refresh mode). This means that BL2 is
always entered in a cold boot scenario.

Once BL2 boots, it determines the boot reason, writes it to shared
memory (BOOT_KIND_BASE) together with the BL31 parameters
(PARAMS_BASE) and jumps to BL31.

To all effects, BL31 is as if it is being entered in reset mode since
it still needs to initialize the rest of the cores; this is the reason
behind using direct shared memory access to  BOOT_KIND_BASE and
PARAMS_BASE instead of using registers to get to those locations (see
el3_common_macros.S and bl31_entrypoint.S for the RESET_TO_BL31 use
case).

Depending on the boot reason BL31 initializes the rest of the cores:
in case of suspend, it uses a MBOX memory region to recover the
program counters.

[1] https://github.com/renesas-rcar/arm-trusted-firmware


Tests
-----

* cpuidle
  -------
   enable kernel's cpuidle arm_idle driver and boot

* system suspend
  --------------
  $ cat suspend.sh
    #!/bin/bash
    i2cset -f -y 7 0x30 0x20 0x0F
    read -p "Switch off SW23 and press return " foo
    echo mem > /sys/power/state

* cpu hotplug:
  ------------
  $ cat offline.sh
    #!/bin/bash
    nbr=$1
    echo 0 > /sys/devices/system/cpu/cpu$nbr/online
    printf "ONLINE:  " && cat /sys/devices/system/cpu/online
    printf "OFFLINE: " && cat /sys/devices/system/cpu/offline

  $ cat online.sh
    #!/bin/bash
    nbr=$1
    echo 1 > /sys/devices/system/cpu/cpu$nbr/online
    printf "ONLINE:  " && cat /sys/devices/system/cpu/online
    printf "OFFLINE: " && cat /sys/devices/system/cpu/offline
Signed-off-by: ldts <jramirez@baylibre.com>

The comments with the prototypes of the register functions of the
console drivers are incorrect. The arguments are wrong. This patch fixes
them.

Change-Id: I38c4b481ee69e840780111c42f03c0752eb6315c
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Signed-off-by: Yann Gautier <yann.gautier@st.com>

commit 97d5db8c reverts an update to the
MMC layer that accompanied the original submission of this MMC driver this
is the right-thing-to-do in terms of the MMC spec.

Unfortunately the reversion also breaks this driver. The issue is the i.MX
controller doesn't want MMC_RSP_48 set for MMC_RESPONSE_R2.

The appropriate place to place that constraint is obviously in
drivers/imx/usdhc/imx_usdhc.c not in the shared MMC codebase. This patch
restores the logic the i.MX controller requires without breaking it for
everyone else.

Fixes: 97d5db8c
Fixes: 2a82a9c9

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Jun Nie <jun.nie@linaro.org>

This way it can be reused by other platforms if needed.

Note that this driver is designed to work with the Versatile Express NOR
flash of Juno and FVP. In said platforms, the memory is organized as an
interleaved memory of two chips with a 16 bit word.

Any platform that wishes to reuse it with a different configuration will
need to modify the driver so that it is more generic.

Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Mark the GICv3, CCI and CCN code only used in Bl31 initialization
with __init to be reclaimed once no longer needed.

Change-Id: I3d77f36758450d9d1d87ecc60bc1c63fe4082667
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Respect official response type and update response to follow
official specification.
All the MMC_RESPONSE_R(_x) are replaced with each corresponding define.

Partly revert 2a82a9c9

 for dw_mmc.c:
Responses R1, R1B and R5 have CRC.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Change-Id: Icd1cdd42afdc78895a9be6c46b414b0a155cfa63
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

It is still a placeholder, but now it is registered correctly by the
macro finish_console_register.

Change-Id: Ic78c966d9be606cbc1a53cec43ead23b32963afe
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ib9eebbdff6f7868e1d1b8c41761cacc7501a25bd
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This driver is deprecated.

Change-Id: Ic6e154a5756e779743b17a329eed4570ccc61389
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I9874883ec33dbf293f607f9779d7c56f23cb8023
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I567a406edb090ae9d109382f6874846a79dd7473
Co-authored-by: Roberto Vargas <roberto.vargas@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The Poplar is broken on eMMC initialization because of commit
2a82a9c9 ("drivers: emmc: dw_mmc: Add response flag into response ID
definition").  It changes the driver behavior on response type handling
in dw_send_cmd(), because MMC_RESPONSE_R(2) and MMC_RESPONSE_R2 are
different things.  MMC core is still sending the former while we already
changed to check the latter in dw_mmc driver.

This patch fixes R2 response type in MMC core code.  It's the same
thing as what commit 94522ff7

 ("drivers: mmc: Fix R3 response type
definition") does for R3 response.

With this fix, Poplar is back to work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Change-Id: I43d2b3a0f672b4902edec3d3a39ffedbb0a701a3
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

Allow AArch32 to use the multi console driver by adding the
required functions

Change-Id: I9e69f18965f320074cf75442d6b0de891aef7936
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

The old driver is now in deprecated_console.S, in a similar way to the
AArch64 driver.

Change-Id: Ib57209c322576c451d466d7406a94adbf01ab8fd
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Allwinner 64-bit SoCs all use the Mentor Graphics MI2CV I2C controller
core, with inverted clear quirk.

Add a glue driver for this.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

The I2C controller on Allwinner SoCs after A31 has a inverted interrupt
clear flag, which needs to be written 1 (rather than 0 on Marvell SoCs
and old Allwinner SoCs) to clear.

Add such a quirk to mi2cv driver common code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which
is also used by Allwinner.

As Mentor Graphics allows a lot of customization, the MI2CV in the two
SoC families are not compatible, and driver modifications are needed.

Extract the common code to a MI2CV driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

The I2C controller found in Marvell A8K SoCs (and some older SoCs) mux
status and baudrate registers into the same address, however, it's a
vendor customization, and the original IP core by Mentor Graphics uses
two different addresses for the two registers.

Use anonymous union in the driver, in order to ease code sharing for
other SoC vendors that use this IP core (Allwinner SoCs that are newly
introduced to mainline ATF use this core).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>