GitLab

The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which
is also used by Allwinner.

As Mentor Graphics allows a lot of customization, the MI2CV in the two
SoC families are not compatible, and driver modifications are needed.

Extract the common code to a MI2CV driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

The I2C controller found in Marvell A8K SoCs (and some older SoCs) mux
status and baudrate registers into the same address, however, it's a
vendor customization, and the original IP core by Mentor Graphics uses
two different addresses for the two registers.

Use anonymous union in the driver, in order to ease code sharing for
other SoC vendors that use this IP core (Allwinner SoCs that are newly
introduced to mainline ATF use this core).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

Add USDHC driver to support boot EMMC. Only initialization
and single/multiple block read are tested.

[bod: fixed checkpatch.pl complaints]
[bod: changed name to imx_usdhc for namespace consistency]
[bod: squashed antecedent fixes into this one patch]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Add missing response type for SWITCH command and STOP_TRANSMISSION
so that controller can be configured accordingly.

[bod: ported this change from Jun's eMMC patches to the MMC driver]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The R3 response type definition should be (1 << 0). Make sure we define the
expected response code in the appropriate fashion.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Add response flag into ID definition so that driver does not
need to handle it again.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Add delay timer API so that it can be called by delay timer
layer and used as delay timer globally.

[bod: changed name from imx_delay_timer -> imx_gpt ]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The Mbed TLS drivers, in order to work, need a heap for internal usage.
This heap, instead of being directly referenced by the drivers, now it
is being accessed indirectly through a pointer. Also, the heap, instead
of being part of the drivers, now it is being received through the
plat_get_mbedtls_heap() function. This function requests a heap from the
current BL image which utilises the Mbed TLS drivers.

Those changes create the opportunity for the Mbed TLS heap to be shared
among different images, thus saving memory. A default heap
implementation is provided but it can be overridden by a platform
specific, optimised implemenetation.

Change-Id: I286a1f10097a9cdcbcd312201eea576c18d157fa
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

It turned out that resetting the RTC time register is not
necessary during initial configuration. Safely remove it
from the sequence.

Change-Id: Id2b9c7db44a8c8dbe88a7f8a21695b72a7fd78ee
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

This patch introduces new helper routines that allow
configuring the individual IRQs to be edge/level-triggered
via GICD_ICFGR registers. This is helpful to modify
the default configuration of the non-secure GIC SPI's, which
are all set during initialization to be level-sensitive.

Change-Id: I23deb4a0381691a686a3cda52405aa1dfd5e56f2
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Use PF instead of PP post-fix, since it is referring to "Phase Final"
(only G3 related register had correct spelling for relevant bit).

Change-Id: Ia5a9c9c78b74b15f7f8adde2c3ef4784c513da2c
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

The biggest comphy index can be equal to 6 so there is no need to use
uint64_t for storing it.

Change-Id: I14c2b68e51678a560815963c72aed0c37068f926
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Add simple driver which allows to configure the memory controller trust
zones. It is responsible for opening mc trustzone window, with
appropriate base address, size and attributes.

Example of usage in upcoming commits.

Change-Id: I8bea17754d31451b305040ee7de331fb8db0c63f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Rename a8k_common.h to armada_common.h to keep the same header
name across all other Marvell Armada platforms.
This is especially useful since various Marvell platforms may
use common platform files and share the driver modules.

Change-Id: I7262105201123d54ccddef9aad4097518f1e38ef
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Pointers should be comparied to NULL.

Fixes: 3fea9c8b

 ("gic: Fix types")
Signed-off-by: Andrew F. Davis <afd@ti.com>

This patch does two main things

- It implements the crash console UART init in assembly, as a
  hard-coded 115200 8N1 assumed from the 24 MHz clock.

  If the clock setup code has not run yet, this code can't work but,
  setting up clocks and clock-gates is way out of scope for this type of
  recovery function.

- It adds code to write a character out of the NXP UART without using any
  stack-based operations when doing so.

- Provides support for crash console in DCE or DTE mode.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

- Adds a simple register read/write abstraction to cut-down on the
  amount of typing and text required to access UART registers in this driver.

- Adds a console getc() callback.

- Adds a console putc() callback, translating '\n' to '\r' + '\n'.

- Initializes the MXC UART, take a crude method of calculating the
  BAUD rate generator. The UART clock-gates must have been enabled prior
  to launching the UART init code.
  Special care needs to be taken to ensure the UBIR is initialized before the
  UBMR and we need to ensure that UCR2.SRST comes good before trying to
  program other registers associated with the UART.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Change-Id: Ifdb0ceec19d267b14d796b5d31f08f7342190484
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I2954a99d5b72069bcb7bac9d6926c6209d6ba881
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I08447b44fffb6e54f9fab957eee369ccbda4247a
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I6a2adef87c20f9279446a54b7e69618fba3d2a25
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I945029ca26ea2e63f0d92c5f33019b882f23bd72
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ib587f12f36810fc7d4f4b8f575195554299b8ed4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

tf_printf and tf_snprintf are now called printf and snprintf, so the
code needs to be updated.

Change-Id: Iffeee97afcd6328c4c2d30830d4923b964682d71
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This allows the console drivers to be implemented in C

Change-Id: Ibac859c4bcef0e92a0dcacc6b58ac19bc69b8342
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

The CCI500 TRM explicitily requires completion of the write
operation before the read operation, and it is not guaranteed
by dmb but it is dsb.

Change-Id: Ieeaa0d1a4b8fcb87108dea9b6de03d9c8a150829
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Because of -Werror, this causes a build error.

Change-Id: I37a8c4bbfe3f2ced5e17981a2814985919ad483b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Replace emmc framework by mmc framework.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Migrate dw_mmc driver from emmc framework to mmc framework. The
emmc framework will be abandoned.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

It should set buswidth and speed of mmc controller before accessing
mmc.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

DMA is always used in mmc driver. So the buffer address should
always follow the DMA limitation.

There're same requirement in mmc_read_blocks()/mmc_write_blocks()
on parameter buf. Since parameter buf comes from io_block driver,
it's already handled in io_block driver.

At here, just make the minimum address alignment on 16 chars.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

mmc_read_blocks()/mmc_write_blocks() derived from io_block_ops_t
type. It means that lba param should be integer type, not
unsigned integer type.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Sending CMD8 before CMD1 just causes to fetch data failure in eMMC.
Check whether it's eMMC first. If it's eMMC, send CMD1 command instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Functions provided by stdio.h such as printf and sprintf are available
in the codebase, but they add a lot of code to the final image if they
are used:

- AArch64: ~4KB
- AArch32: ~2KB in T32, ~3KB in A32

tf_printf and tf_snprintf are a lot more simple, but it is preferable
to use them when possible because they are also used in common code.

Change-Id: Id09fd2b486198fe3d79276e2c27931595b7ba60e
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

We had exit but we didn't have atexit, and we were calling panic and
tf_printf from exit, which generated a dependency from exit to them.
Having atexit allows to set a different function pointer in every image.

Change-Id: I95b9556d680d96249ed3b14da159b6f417da7661
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Mbebtls include paths are controlled by the user using the variable
MBEDTLS_DIR and they are out of the TF source tree. Since these
includes have a different origin it is better to move them to a
different variable.

This change makes easier for the romlib Makefile to parse the include
paths.

Change-Id: I3e4c99300f1012bc7f88c6b9f5bc0ec1f7b5aa8d
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

TF Makefile was linking all the objects files generated for the
Mbed TLS library instead of creating a static library that could be
used in the linking stage.

Change-Id: I8e4cd843ef56033c9d3faeee71601d110b7e4c12
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

A new function mmc_reset_to_idle is also created.
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Fix violations of MISRA C-2012 Rules 10.1, 10.3 and 10.4.

Change-Id: I13c6acda798c1666892f630f097a23e68748f9e4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

When a platform enables its caches before it initializes the
GICC/GICR interface then explicit cache maintenance is not
needed. Remove these here.
Signed-off-by: Andrew F. Davis <afd@ti.com>