GitLab

This patch maps the devices in the first GB of the system address map
on the FVP into the S-EL1&0 translation regime when SPM support is
enabled. This grants the Secure Partition access to the devices in
this region, for example the memory-mapped Generic Timer device.

Change-Id: I3aeea65f859ecbe83efde2acee20c55500c451bc
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

`assert(e)` was used in place of `if (e) ERROR()` when sec_protect()
was ported from hikey fork so the logic should have been reversed.

Fixes: 3d5d9f5a ("hikey: configure the top 16MB of DRAM as secure")
Fixes: 52988b38

 ("hikey: configure 4 MB of secure DRAM for OP-TEE
Secure Data Path")
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Victor Chong <victor.chong@linaro.org>

UniPhier platform implements non-TF boot ROM.  Prior to the BL2-AT-EL3
support, BL1 (worked as a pseudo ROM) was needed just for ensuring BL2
is entered at EL1-S.  Now, this platform is able to avoid this waste.

Enable the BL2_AT_EL3 option, and remove BL1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The warm boot mailbox code is compiled if PROGRAMMABLE_RESET_ADDRESS
is disabled.

The warm boot mailbox is useless for UniPhier SoC family because BL1
is not the first image.  The UniPhier platform implements non-TF ROM,
then BL1 works as a pseudo ROM, so it is never executed in the warm
boot.

The reset vector address is not actually programmable for UniPhier
platform, but it should not hurt to enable PROGRAMMABLE_RESET_ADDRESS
to disable the mailbox and remove pointless plat_get_my_entrypoint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Update the memory firewall configuration to reserve 4 MB of secure RAM
for use by the kernel and OP-TEE as the Secure Data Path pool.
Note that this address range (0x3E800000 - 0x3EC00000) falls in the
range already set aside by UEFI (which reserves the upper 32 MB of the
1GB DRAM for OP-TEE [1]) and was previously unused.

[1] https://github.com/96boards-hikey/edk2/blob/hikey/HisiPkg/HiKeyPkg/Library/HiKeyLib/HiKeyMem.c#L44

Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Victor Chong <victor.chong@linaro.org>

DRAM region 0x3f000000 - 0x3fffffff is reserved for OP-TEE and should
therefore be accessible only from secure world.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Victor Chong <victor.chong@linaro.org>

The `override ERROR_DEPRECATION = 1` setting in uniphier platform
makes deprecation of API difficult. Hence removing the same. This
flag should be specified on the command line if needed.

Change-Id: I8c82d8d13944e450a8cd636de3326137c04d7560
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Let bl1 and bl2 have the ability to load images from emmc instead of
dram (mmap).
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

When some interrupts are configured as group 0 in GICv2, these
interrupts trigger FIQ signal; this results in the Linux kernel panic
by reporting log: "Bad mode in FIQ handler detected on CPU0, code
0x00000000 -- Unknown/Uncategorized".  Unfortunately from kernel side it
has no permission to read the GIC register for group 0 interrupts so we
have no chance to get to know which interrupt is configured as secure
interrupt and cause the kernel panic.

For upper reason, this commit enables FIQ exception handling for
SPD_none case.  If the system has not enabled SPD the FIQ interrupt is
trapped into EL3 and the FIQ handler can report the interrupt number so
we can easily narrow down which FIQ introduce unexpected interrupt.
After enable SPD we can rely on SPD interrupt route model to handle FIQ.
Signed-off-by: Leo Yan <leo.yan@linaro.org>

This patch changes all Rockchip platforms to use the new
MULTI_CONSOLE_API. The platform-specific plat_crash_console
implementations are removed so that the platform can use the ones from
the common platform code instead.

Also change the registers used in plat_crash_print_regs. The existing
use of x16 and x17 has always been illegal, since those registers are
reserved for use by the linker as a temporary scratch registers in
intra-procedure-call veneers and can never be expected to maintain their
values across a function call.

Change-Id: I8249424150be8d5543ed4af93b56756795a5288f
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch changes all Rockchip platforms to initialize the serial
console with information supplied by coreboot rather than hardcoded
base address and divisor values if BL31 is run on top of coreboot.
Moving the BL2-to-BL31 parameter parsing as early as possible to ensure
that the console is available for all following code.

Also update the Rockchip platform to use MULTI_CONSOLE_API.

Change-Id: I670d350fa2f8b8133539f91ac14977ab47db60d9
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch expands the weak stubs for the plat_crash_console_xxx
functions in common platform code to use the new console API for crash
output. This should make crash console output "just work" for most cases
without the need for the platform to explicitly set up a crash console.
For cases where the normal console framework doesn't work (e.g. very
early crashes, before the platform can register any consoles), platforms
are still able to override the functions just like before.

This feature requires the MULTI_CONSOLE_API compile-time flag to work.
For builds which don't have it set, this patch has no practical effect.

Change-Id: I80dd161cb43f9db59a0bad2dae33c6560cfac584
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch modifies the makefiles to avoid the definition
of BL1_SOURCES and BL2_SOURCES in the tbbr makefiles, and
it lets to the platform makefiles to define them if they
actually need these images. In the case of BL2_AT_EL3
BL1 will not be needed usually because the Boot ROM will
jump directly to BL2.

Change-Id: Ib6845a260633a22a646088629bcd7387fe35dcf9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.

The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:

	--data cluster0.cpu0=bl2.bin@0x4001000
	-C cluster0.cpu0.RVBAR=0x4001000

These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.

Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch enables BL2 to execute at the highest exception level
without any dependancy on TF BL1. This enables platforms which already
have a non-TF Boot ROM to directly load and execute BL2 and subsequent BL
stages without need for BL1.  This is not currently possible because
BL2 executes at S-EL1 and cannot jump straight to EL3.

Change-Id: Ief1efca4598560b1b8c8e61fbe26d1f44e929d69
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

At early time, the CPU CA73 retention state has been supported on
Hikey960.  Later we found the system has the hang issue and for
resolving this issue Hisilicon released new MCU firmware, but
unfortunately the new MCU firmware has side effect and results in the
CA73 CPU cannot really enter retention state and roll back to WFI state.

After discussion we cannot see the possibility to enable CA73 retention
state anymore on Hikey960, based on this conclusion we should remove
this state supporting from ARM-TF and roll back to WFI state only.  We
will commit one patch to remove CA73 CPU retention state in kernel DT
binding as well.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>

This reverts commit fdae60b6.

The commit fdae60b6

 changed the
parameter encoding for the hikey960.  However that implies a DT change
in the kernel side.  After submitting the DT change for upstreaming,
the backward compatibility issue and the interface change raise some
concerns from the Linux community about the issues related to kernel <->
ATF alignment.  There is no way to detect a mis-alignment of those
without a deep knowledge of the ATF and the kernel.  Furthermore, the
failing calls to PSCI in the idle path (because of bad parameters), will
lead to busy looping, implying: thermal issues and extra energy
consumption.

In regard of the Linux community concerns, the potential issues when the
ATF and the kernel are not aligned, it is preferable to revert the
commit.

Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Co-authored-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>

Change-Id: I504d3f65ca5829bc1f4ebadb764931f8379ee81f
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Set IOC_AO_IOMG_033 function from GPIO213 to PCIE_CLKREQ_N

bit[0-2]:  000: GPIO_213;
           001: PCIE_CLKREQ_N;
           010: GPIO_018_SH;
           100: GPIO_014_SE;
           110: FAC_TEST24;
           111: FAC_TEST24;
bit[3-31]: reserved
Signed-off-by: Guangtao Zhang <zhangguangtao@hisilicon.com>
Tested-by: Yao Chen <chenyao11@huawei.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Use zynqmp_ipi APIs to access IPI registers in pm_service.
As the zynqmp_ipi APIs doesn't cover IPI buffers, the pm_ipi
in pm_service will still directly access the IPI buffers.
Signed-off-by: Wendy Liang <jliang@xilinx.com>

Add IPI mailbox service to manage Xilinx ZynqMP IPI(Inter Processors
Interrupt) access.
Signed-off-by: Wendy Liang <jliang@xilinx.com>

Previously, ZynqMP IPI in ATF is only for ZynqMP PM,
This patch is to have a ZynqMP IPI implementation to handle
both ZynqMP PM IPI requirement and IPI mailbox service requirement
which will be introduced next.

We control IPI agents registers access but not IPI buffers access in
this implementation. Each IPI mailbox user will directly access the
IPI buffers.
Signed-off-by: Wendy Liang <jliang@xilinx.com>

It is not necessary to read data from stdin.  The input file name
is ripped off by -n option, anyway.  I still use the redirect for
the output to specify the output file name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

To allow BL31 to grow in SRAM, move TSP in TZC secured DRAM
by default.

Increase the BL31 max limit by one page.

Change-Id: Idd3479be02f0f9bafac2f275376d7db0c2015431
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

The build log should be indented with two spaces for correct alignment.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The current IO block buffer overlaps with BL2 image location.
So, BL2 may corrupt itself.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.

Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

This patch overhauls the console API to allow for multiple console
instances of different drivers that are active at the same time. Instead
of binding to well-known function names (like console_core_init),
consoles now provide a register function (e.g. console_16550_register())
that will hook them into the list of active consoles. All console
operations will be dispatched to all consoles currently in the list.

The new API will be selected by the build-time option MULTI_CONSOLE_API,
which defaults to ${ERROR_DEPRECATED} for now. The old console API code
will be retained to stay backwards-compatible to older platforms, but
should no longer be used for any newly added platforms and can hopefully
be removed at some point in the future.

The new console API is intended to be used for both normal (bootup) and
crash use cases, freeing platforms of the need to set up the crash
console separately. Consoles can be individually configured to be active
active at boot (until first handoff to EL2), at runtime (after first
handoff to EL2), and/or after a crash. Console drivers should set a sane
default upon registration that can be overridden with the
console_set_scope() call. Code to hook up the crash reporting mechanism
to this framework will be added with a later patch.

This patch only affects AArch64, but the new API could easily be ported
to AArch32 as well if desired.

Change-Id: I35c5aa2cb3f719cfddd15565eb13c7cde4162549
Signed-off-by: Julius Werner <jwerner@chromium.org>

The current Rockchip platform code retains the "common" default panic
handler which simply hangs the system (until the watchdog kicks in, if
enabled). This is usually not a great user experience.

This patch implements a Rockchip-specific panic handler that calls the
platform's reboot implementation to reset the system.

Change-Id: I4cbe09c48f1b3f86ebdfc0108c186565f9ffc119
Signed-off-by: Julius Werner <jwerner@chromium.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>

The security properties of some IP blocks are configured to secure mode
after reset. This means these IP blocks can only be accessed by cpus
in secure state by default. These should be configured correclty as needed.
Signed-off-by: y00241285 <yyangwei.yangwei@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>

This is currently the maximum allowed without affecting bootup.
Signed-off-by: Victor Chong <victor.chong@linaro.org>

to PLAT_POPLAR_NS_IMAGE_OFFSET
Signed-off-by: Victor Chong <victor.chong@linaro.org>

Per
https://github.com/sdrobertw/Poplar/blob/master/HardwareDocs/Processor_Datasheet_v2XX.pdf


there are 13 groups of GPIO controllers, not 12.
Signed-off-by: Victor Chong <victor.chong@linaro.org>

After returning from SYSTEM_SUSPEND state, BL31 reconfigures the
TrustZone Controller during the boot sequence. If BL31 is placed in
TZC-secured DRAM, it will try to change the permissions of the memory it
is being executed from, causing an exception.

The solution is to disable SYSTEM_SUSPEND when the Trusted Firmware has
been compiled with ``ARM_BL31_IN_DRAM=1``.

Change-Id: I96dc50decaacd469327c6b591d07964726e58db4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Common code mustn't include ARM platforms headers.

Change-Id: Ib6e4f5a77c2d095e6e8c3ad89c89cb1959cd3043
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

ARM Power State Coordination Interface (ARM DEN 0022D) chapter
6.5 "Recommended StateID Encoding" defines the state ID which can be
used by platforms. The recommended power states can be presented by
below values; and it divides into three fields, every field has 4 bits
to present power states corresponding to core level, cluster level and
system level.

  0: Run
  1: Standby
  2: Retention
  3: Powerdown

This commit changes to use upper recommended power states definition on
Hikey960; and changes the power state validate function to check the
power state passed from kernel side.
Signed-off-by: Leo Yan <leo.yan@linaro.org>

This patch allows non-secure bus masters to access TZC region0 as well
as the EL3 Payload itself.

Change-Id: I7e44f2673a2992920d41503fb4c57bd7fb30747a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>