GitLab

TLBI instructions for EL3 won't have the desired effect under specific
circumstances in Cortex-A57 r0p0. The workaround is to execute DSB and
TLBI twice each time.

Even though this errata is only needed in r0p0, the current errata
framework is not prepared to apply run-time workarounds. The current one
is always applied if compiled in, regardless of the CPU or its revision.

This errata has been enabled for Juno.

The `DSB` instruction used when initializing the translation tables has
been changed to `DSB ISH` as an optimization and to be consistent with
the barriers used for the workaround.

Change-Id: Ifc1d70b79cb5e0d87e90d88d376a59385667d338
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The files affected by this patch don't really depend on `xlat_tables.h`.
By changing the included file it becomes easier to switch between the
two versions of the translation tables library.

Change-Id: Idae9171c490e0865cb55883b19eaf942457c4ccc
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Sorry to miss the security configuration for SRAM, if we don't support
it, somebody may modify the comment of SRAM in the non-secure space.
Let's fix this issue.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This fixes code that set a tFC value in a register using the tRFC
value instead.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The F1 CAS latency setting was not bit shifted, which resulted in
setting the DRAM additive latency value instead.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

On resume, we use the DFS hardware to switch frequency index,
followed by a full training sequence on that index. Leaving
the DFS training modules enabled causes issues with the full
training done at resume. We also only needs these enabled
during a call to ddr_set_rate during runtime, so there's no
issue disabling them at the end of ddr_set_rate.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This moves the setting of the DQS drive strength to the M0 to minimize
the impact on DDR transactions. We need to have the DQS drive strength
changed for data training, which is triggered by the M0, but it also
needs to be changed back when data training is finished.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes an optimization to not recalculate parameters if the
frequency index being switched to hold the next frequency. This is
because some registers do not have a copy per frequency index, so this
optimization might be causing problems.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

We were getting far off values on resume for the RX_CAL_DQS values.
This saves and restores the values for suspend/resume until the root
of the problem is figured out
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

These macros were accidentally deleted in a previous cleanup. This
slipped through because the code using them is currently unused, but
that may change in the future.
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch shuffles the M0 Makefile flags around a bit trying to make
their purpose clearer and remove duplication. Since all three build
steps (compiling, assembling, linking) actually call GCC, remove the
misleading aliases $(AS) and $(LD) to avoid confusion that those tools
might be called directly. Split flags into a common group that has
meaning for all three steps and separate variables specific to each
step. Remove -nostartfiles which is a strict subset of -nostdlib.

Also add explicit parameters for -mfloat-abi=soft, -fomit-frame-pointer
and -fno-common. If omitted these settings depend on the toolchain's
built-in default and cause various problems if they resolve to
unexpected values.
Signed-off-by: Julius Werner <jwerner@chromium.org>

The goal is that make clear the secure and SoC codes. Now cleaning them
will help secure code extensions for RK3399 in the future.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

Maybe the coreboot will reference the BL31 parameters (e.g the TZRAM_BASE
and TZRAM_SIZE for DDR secure regions), we can split them and don't have
to hardcode the range in two places.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

Move the BL31 loaded base address 0x10000 to 0x1000, and configure
the the memory range 0~1MB is secure, the goal is that make sure
the BL31 image will be not modified.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

So far, there are more and more features are supported on the RK3399,
meanwhile, these features are increasingly being defined and intertwined.
It's time to clean up and make them clearer.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This removes waiting for vblank on the M0 during ddrfreq transitions.
That will now be done in the kernel to allow scheduling to be done on
the CPU core that changes the ddr frequency. Waiting for vblank in
the M0 would have the CPU core that waits on the M0 spin looping for
up to 16ms (1 frame for the display).
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

we will set PMU_CRU_GATEDIS_CON0 when idle port, it will enable
all clock, for save power consumption, we need to restore old value
when finish it.
Signed-off-by: Lin Huang <hl@rock-chips.com>

As rk3399 TRM1.1 document show, when set PMU_CRU_GATEDIS_CON0/1
register, it need set the write_mask bit (bit16 ~ bit31), but as
we test, it not need it. So need to correct the setting way, otherwise
it will set wrong value to this register.
Signed-off-by: Lin Huang <hl@rock-chips.com>

We found that the DUT will be hanged if we don't set the bit_1 of the
PMUCRU_GATEDIS_CON0. But, from the TRM, there is weird that the bit_1
is set the clk_center1_gating_dis, not clk_pmum0_gating_dis. Is the
TRM incorrect? We need to check it with the IC team and re-clean the
commit message and explain it tomorrow.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This patch do following things:
1. Request hresetn_cm0s_pmu_req first then request
   poresetn_cm0s_pmu_req during M0 enable.
2. Do not diable M0 clock for ddr dvfs.
3. Correct the clk_pmum0_gating_dis bit, it is BIT0 not BIT1
4. do not set/clear hclk_noc_pmu_en in M0 code, it does not relate
   to the M0 clock.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

When vop is disabled and we read the vop register the system will
hang, so check vop status when we wait for the DMA finish flag to
avoid this sitiuation. This is done by checking for standby, DMA stop
mode, and disabled window states. Any one of these will prevent the
DMA finish flag from triggering.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

There is system timer in m0, we can use it to implement a set of
stopwatch functions for measuring timeouts.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The phy pll needs to get 2X frequency to the DDR, so set the
pll_postdiv to 0.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

For ddr dfs stable, We need to enable ddr CA training
when do ddr dfs.
Signed-off-by: Lin Huang <hl@rock-chips.com>

This fixes a hang with setting the DRAM rate based on a race condition
with the M0 which sets the DRAM rate. The AP can also starve the M0,
so this also delays the AP reads to the DONE parameter for the M0.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This enables per CS training at 666MHz and above for ddrfreq per
vendor recommendation. Since the threshold was used for latency was
the same value, this also adds a new value for that.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This patch sets the frequency configuration of the next DRAM DFS index
to the configuration of the current index. This does not perform a
frequency transition. It just configures registers so the training on
resume for both indices will be correct.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

We used dcf do ddr frequency scaling, but we just include a dcf
binary, it hard to maintain later, we have M0 compile flow in ATF,
and M0 can also work for ddr frequency scaling, so let's use it.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This makes the file consistently use tabs instead of mixing in spaces.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

Since the ATF project, we usually use the mmio_read_32 and
mmio_write_32. And the mmio_write_32, the firse parameter
is ADDR, the second is VALUE. In order to style consistency:

1/ rename readl/writel to mmio_read_32/mmio_write_32
2/ for keeping the same with mmio_write_32 in the ATF project,
   swap the order of the parameters for M0 mmio_write_32
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Lin Huang <hl@rock-chips.com>

when dram frequency below 260MHz, phy master dll may unlock, so
let phy master dll working at dll bypass mode when frequency is
below 260MHz.
Signed-off-by: Lin Huang <hl@rock-chips.com>

we can reuse the dram config from loader, so we can remove dram_init()
and dts_timing_receive() funciton in dram.c, add the dram_set_odt_pd()
function to get the odt and auto power down parameter from kernel.

This also removes the dcf_code_init function to allow the system to
actually boot.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This patch adds the pwr_domain_power_down_wfi() handler for Tegra
platforms which in turn executes the soc specific `power_down_wfi`
handler.

Change-Id: I5deecc09959db3c3d73f928f5c871966331cfd95
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch maps the TZDRAM carveout used by the BL31. In the near
future BL31 would be running from the TZRAM for security and
performance reasons. The only downside to this solution is that
the TZRAM loses its state in System Suspend. So, we map the TZDRAM
carveout that the BL31 would use to save its state before entering
System Suspend.

Change-Id: Id5bda7e9864afd270cf86418c703fa61c2cb095f
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch increases the BL31 image size for all Tegra platforms to
256KB, so that we can relocate BL31 to TZSRAM on supported chips.

Change-Id: I467063c68632b53b5d4ef8ff1f76f5988096bd9c
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch uses the Memory controller driver's handler to restore
its settings and moves the other chip specific code to their own
'pwr_domain_on_finish' handlers.

Change-Id: I3c9d23bdab9e2e3c05034ff6812cf941ccd7a75e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch moves the code to disable DCO operations out from common
CPU files. This allows the platform code to call thsi API as and
when required. There are certain CPU power down states which require
the DCO to be kept ON and platforms can decide selectively now.

Change-Id: Icb946fe2545a7d8c5903c420d1ee169c4921a2d1
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch enables the PSCI_EXTENDED_STATE_ID macro. Tegra platforms
have moved on to using the extended state ID for CPU_SUSPEND, where
the NS world passes the state ID and wakeup time as part of the
state ID field.

Change-Id: Ie8b0fec285d8b2330bc26ff239a4f628425c9fcf
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The platform power states, PLAT_MAX_RET_STATE and PLAT_MAX_OFF_STATE,
can change on Tegra SoCs and so should be defined per-soc.

This patch moves these macro definitions to individual SoC's tegra_def.h
files.

Change-Id: Ib9b2752bc4d79cef6f79bee49882d340f71977a2
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch introduces a function to secure the on-chip TZRAM memory. The
Tegra132 and Tegra210 chips do not have a compelling use case to lock the
TZRAM. The trusted OS owns the TZRAM aperture on these chips and so it
can take care of locking the aperture. This might not be true for future
chips and this patch makes the TZRAM programming flexible.

Change-Id: I3ac9f1de1b792ccd23d4ded274784bbab2ea224a
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>