GitLab

Move doimage utility from toos/doimage to tools/marvell/doimage.
This is done for supporting mode Marvell tools in the future.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Some of COMPHY parameters depends on the hw connection between the SoC
and the PHY, which can vary on different boards e.g. due to different
wires length. Define the "porting layer" with some defaults
parameters. It ease updating static values which needs to be updated due
to board differences, which are now grouped in one place.

Example porting layer for a8k-db is under:
plat/marvell/a8k/a80x0/board/phy-porting-layer.h

If for some boards parameters are not defined (missing
phy-porting-layer.h), the default values are used
(drivers/marvell/comphy/phy-default-porting-layer.h)
and the following compilation warning is show:
"Using default comphy params - you may need to suit them to your board".

The common COMPHY driver code is extracted in order to be shared with
future COMPHY driver for A3700 SoC platforms
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Fix the include protector to be in sync with file name
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Add 16-bit variant of mmio_clrsetbits function
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

rcar_gen3: initial support

Allow D-Cache to remain on during core power-down

Optimize bakery locks when HW_ASSISTED_COHERENCY is enabled

plat/arm: relocate the jump_if_cpu_midr macro.

plat/arm: Small reorganization of platform code

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

Signed-off-by: ldts <jramirez@baylibre.com>

 - ddr
 - pfc [pin function controller]
 - qos [bandwidth]

checkpatch.pl is generating too many errors.

Reference code:
==============

rar_gen3: IPL and Secure Monitor Rev1.0.22
https://github.com/renesas-rcar/arm-trusted-firmware [rcar_gen3]

Author: Takuya Sakata <takuya.sakata.wz@bp.renesas.com>
Date:   Thu Aug 30 21:26:41 2018 +0900
	Update IPL and Secure Monitor Rev1.0.22

General Information:
===================

This port has been tested on the Salvator-X Soc_id r8a7795 revision
ES1.1 (uses an SPD).

Build Tested:
-------------
ATFW_OPT="LSI=H3 RCAR_DRAM_SPLIT=1 RCAR_LOSSY_ENABLE=1"
MBEDTLS_DIR=$mbedtls

$ make clean bl2 bl31 rcar PLAT=rcar ${ATFW_OPT} SPD=opteed

Other dependencies:
------------------
* mbed_tls:
  git@github.com:ARMmbed/mbedtls.git [devel]

  Merge: 68dbc94 f34a4c1
  Author: Simon Butcher <simon.butcher@arm.com>
  Date:   Thu Aug 30 00:57:28 2018 +0100

* optee_os:
  https://github.com/BayLibre/optee_os



  Until it gets merged into OP-TEE, the port requires Renesas' Trusted
  Environment with a modification to support power management.

  Author: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
  Date:   Thu Aug 30 16:49:49 2018 +0200
    plat-rcar: cpu-suspend: handle the power level
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>

* u-boot:
  The port has beent tested using mainline uboot.

  Author: Fabio Estevam <festevam@gmail.com>
  Date:   Tue Sep 4 10:23:12 2018 -0300

*linux:
  The port has beent tested using mainline kernel.

  Author: Linus Torvalds <torvalds@linux-foundation.org>
  Date:   Sun Sep 16 11:52:37 2018 -0700
      Linux 4.19-rc4

Overview
---------

BOOTROM starts the cpu at EL3; In this port BL2 will therefore be entered
at this exception level (the Renesas' ATF reference tree [1] resets into
EL1 before entering BL2 - see its bl2.ld.S)

BL2 initializes DDR (and i2c to talk to the PMIC on some platforms)
before determining the boot reason (cold or warm).

During suspend all CPUs are switched off and the DDR is put in
backup mode (some kind of self-refresh mode). This means that BL2 is
always entered in a cold boot scenario.

Once BL2 boots, it determines the boot reason, writes it to shared
memory (BOOT_KIND_BASE) together with the BL31 parameters
(PARAMS_BASE) and jumps to BL31.

To all effects, BL31 is as if it is being entered in reset mode since
it still needs to initialize the rest of the cores; this is the reason
behind using direct shared memory access to  BOOT_KIND_BASE and
PARAMS_BASE instead of using registers to get to those locations (see
el3_common_macros.S and bl31_entrypoint.S for the RESET_TO_BL31 use
case).

Depending on the boot reason BL31 initializes the rest of the cores:
in case of suspend, it uses a MBOX memory region to recover the
program counters.

[1] https://github.com/renesas-rcar/arm-trusted-firmware


Tests
-----

* cpuidle
  -------
   enable kernel's cpuidle arm_idle driver and boot

* system suspend
  --------------
  $ cat suspend.sh
    #!/bin/bash
    i2cset -f -y 7 0x30 0x20 0x0F
    read -p "Switch off SW23 and press return " foo
    echo mem > /sys/power/state

* cpu hotplug:
  ------------
  $ cat offline.sh
    #!/bin/bash
    nbr=$1
    echo 0 > /sys/devices/system/cpu/cpu$nbr/online
    printf "ONLINE:  " && cat /sys/devices/system/cpu/online
    printf "OFFLINE: " && cat /sys/devices/system/cpu/offline

  $ cat online.sh
    #!/bin/bash
    nbr=$1
    echo 1 > /sys/devices/system/cpu/cpu$nbr/online
    printf "ONLINE:  " && cat /sys/devices/system/cpu/online
    printf "OFFLINE: " && cat /sys/devices/system/cpu/offline
Signed-off-by: ldts <jramirez@baylibre.com>

Leave the caches on and explicitly flush any data that
may be stale when the core is powered down. This prevents
non-coherent interconnect access which has negative side-
effects on AM65x.
Signed-off-by: Andrew F. Davis <afd@ti.com>

When HW_ASSISTED_COHERENCY is enabled we can use spinlocks
instead of using the more complex and slower bakery algorithm.

Change-Id: I9d791a70050d599241169b9160a67e57d5506564
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

macro jump_if_cpu_midr is used commonly by many arm platform.
It has now been relocated to common place to remove duplication
of code.

Change-Id: Ic0876097dbc085df4f90eadb4b7687dde7c726da
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>

drivers: partition: correct compilation error in VERBOSE mode

Introduce object pool allocator

pl011: cnds: cbmem: 16550: Fix comments

The comments with the prototypes of the register functions of the
console drivers are incorrect. The arguments are wrong. This patch fixes
them.

Change-Id: I38c4b481ee69e840780111c42f03c0752eb6315c
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Makefile: Support totally quiet output with -s

plat/arm: Fix misra warnings in platform code

drivers: imx: mxc_usdhc: Do not set MMC_RSP_48 for MMC_RESPONSE_R2

PSCI cache flush and comment fixup

Change-Id: Ica944acc474a099219d50b041cfaeabd4f3d362f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

The object pool allocator provides a simplistic interface to manage
allocation in a fixed-size static array. The caller creates a static
"object pool" out of such an array and may then call pool_alloc() to
get the next available object within the pool. There is also a variant
to get multiple consecutive objects: pool_alloc_n().

Note that this interface does not provide any way to free the objects
afterwards. This is by design and it is not a limitation. We do not
want to introduce complexity induced by memory freeing, such as
use-after-free bugs, memory fragmentation and so on.

Change-Id: Iefc2e153767851fbde5841a295f92ae48adda71f
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Signed-off-by: Yann Gautier <yann.gautier@st.com>